Class 2B Tap Drill Size: How Much Thread the Limits Allow
A class 2B hole leaves at most about 83% thread. The least it can leave is 53.0% to 67.2%, depending on the thread. We worked that out for 30 inch threads: a 70% thread fits inside 2B on all 30, 65% on 14, 60% on 6 and 50% on none. So the common advice that 60% thread is enough can put a hole out of tolerance.
How many threads each percentage fits
| Thread percentage | Hole inside 2B | Share of threads |
|---|---|---|
| 50% | 0 of 30 | 0% |
| 55% | 2 of 30 | 7% |
| 60% | 6 of 30 | 20% |
| 65% | 14 of 30 | 47% |
| 70% | 30 of 30 | 100% |
| 75% | 30 of 30 | 100% |
| 80% | 30 of 30 | 100% |
| 85% | 0 of 30 | 0% |
Each row asks one question: if you could cut a hole for exactly this percentage, would it be inside the thread's 2B limits? Real drills come in steps, which the next table deals with.
Every thread, with the biggest drill inside 2B
The last column helps with tough materials. It is the biggest number, letter or 1/64 in fractional drill that stays inside the limits, so it is the easiest on the tap while still meeting class 2B. On ten threads the only such drill is the standard one. Highlighted rows are threads whose standard drill is outside the limits.
| Thread | 2B minor diameter | Thread allowed | Standard drill | Against the limits | Biggest inch drill inside 2B |
|---|---|---|---|---|---|
| #0-80 | 0.0465 to 0.0514 in | 53.0% to 83.1% | 3/64 in 81% | Inside | 3/64 in 81% |
| #2-56 | 0.0667 to 0.0737 in | 53.0% to 83.2% | #50 69% | Inside | #49 56% |
| #4-40 | 0.0849 to 0.0939 in | 55.7% to 83.4% | #43 71% | Inside | 3/32 in 56% |
| #5-40 | 0.0979 to 0.1062 in | 57.9% to 83.4% | #38 72% | Inside | #37 65% |
| #6-32 | 0.1040 to 0.1140 in | 59.1% to 83.8% | #36 78% | Inside | #33 62% |
| #6-40 | 0.1110 to 0.1190 in | 58.5% to 83.1% | #33 77% | Inside | #32 68% |
| #8-32 | 0.1300 to 0.1390 in | 61.6% to 83.8% | #29 69% | Inside | #29 69% |
| #10-24 | 0.1450 to 0.1560 in | 62.8% to 83.1% | #25 75% | Inside | #23 67% |
| #10-32 | 0.1560 to 0.1640 in | 64.0% to 83.8% | #21 76% | Inside | #20 71% |
| #12-24 | 0.1710 to 0.1810 in | 64.7% to 83.1% | #16 72% | Inside | #15 67% |
| 1/4-20 | 0.1960 to 0.2070 in | 66.2% to 83.1% | #7 75% | Inside | #5 69% |
| 5/16-18 | 0.2520 to 0.2650 in | 65.8% to 83.8% | letter F 77% | Inside | letter G 71% |
| 3/8-16 | 0.3070 to 0.3210 in | 66.5% to 83.8% | 5/16 in 77% | Inside | letter O 73% |
| 7/16-14 | 0.3600 to 0.3760 in | 66.3% to 83.5% | letter U 75% | Inside | 3/8 in 67% |
| 1/2-13 | 0.4170 to 0.4340 in | 66.0% to 83.1% | 27/64 in 78% | Inside | 27/64 in 78% |
| 9/16-12 | 0.4720 to 0.4900 in | 67.0% to 83.6% | 31/64 in 72% | Inside | 31/64 in 72% |
| 5/8-11 | 0.5270 to 0.5460 in | 66.9% to 83.0% | 17/32 in 79% | Inside | 17/32 in 79% |
| 3/4-10 | 0.6420 to 0.6630 in | 67.0% to 83.1% | 21/32 in 72% | Inside | 21/32 in 72% |
| 7/8-9 | 0.7550 to 0.7780 in | 67.2% to 83.1% | 49/64 in 76% | Inside | 49/64 in 76% |
| 1/4-28 | 0.2110 to 0.2200 in | 64.7% to 84.1% | #3 80% | Inside | 7/32 in 67% |
| 5/16-24 | 0.2670 to 0.2770 in | 65.6% to 84.1% | letter I 75% | Inside | letter J 66% |
| 3/8-24 | 0.3300 to 0.3400 in | 64.7% to 83.1% | letter Q 79% | Inside | letter R 67% |
| 7/16-20 | 0.3830 to 0.3950 in | 65.4% to 83.9% | 25/64 in 72% | Inside | 25/64 in 72% |
| 1/2-20 | 0.4460 to 0.4570 in | 66.2% to 83.1% | 29/64 in 72% | Inside | 29/64 in 72% |
| 9/16-18 | 0.5020 to 0.5150 in | 65.8% to 83.8% | 33/64 in 65% | Over the max by 0.0006 in | none; 12.9 mm 76% |
| 5/8-18 | 0.5650 to 0.5780 in | 65.1% to 83.1% | 37/64 in 65% | Over the max by 0.0001 in | none; 14.5 mm 75% |
| 3/4-16 | 0.6820 to 0.6960 in | 66.5% to 83.8% | 11/16 in 77% | Inside | 11/16 in 77% |
| 7/8-14 | 0.7980 to 0.8140 in | 65.7% to 83.0% | 13/16 in 67% | Inside | 13/16 in 67% |
| 1/2-28 | 0.4610 to 0.4700 in | 64.7% to 84.1% | 15/32 in 67% | Inside | 15/32 in 67% |
| 5/8-24 | 0.5800 to 0.5900 in | 64.7% to 83.1% | 37/64 in 87% | Under the min by 0.0019 in | none; 14.8 mm 78% |
Why the top is always about 83%
The 2B minimum sits close to the major diameter minus 1.0825 times the pitch (Wikipedia). A full thread takes 1.299 pitches, and 1.0825 / 1.299 is 83.3%. In these limits the top runs from 83.0% to 84.1%, so a drill that would leave more than about 84% is under the minimum on every thread here.
The bottom moves. #0-80 can go as low as 53.0%, and 7/8-9 only to 67.2%. Below 1/4 in the floor climbs from 53.0% to 64.7%. From 1/4 in up it stays between 64.7% and 67.2%.
What this means for the 60% advice
The OSG chart says 55 to 65% thread is enough for most requirements, and it also warns that a higher percentage may be needed to meet the minor diameter limits of the class specified. These numbers show how often that warning applies. Our own steel drill, aimed at 60%, cuts a hole over the 2B maximum on 21 of 30 threads, and our stainless drill, aimed at 50%, on 28.
That does not make those drills wrong. Strength and class limits are separate questions, and if a drawing names no class, a lower percentage makes tapping easier. If the drawing says 2B, the limits decide, and 70% is the lowest round figure here that fits every thread. The thread percentage chart covers the strength side.
Class 6H is tighter on the low side
Using the Emuge limits for the 17 metric threads here, 75% fits 17, 70% fits 15, 65% fits 6 and 60% fits no. The two that 70% misses are M24 and M30. The metric formula test goes through those threads one by one.
Limits of this study
This is arithmetic on published limits, using each drill's nominal size. We did not drill or gauge any holes, and a real hole can run oversize, so a drill right at the maximum may not pass. Minor diameter is also only one limit: a gauge checks pitch diameter too, and the tap sets that. The limits are for class 2B cut threads. Form taps follow their own chart.
FAQ
What is the tap drill size for a class 2B thread?
Any drill whose hole falls inside the thread's 2B minor diameter limits. For 1/4-20 those are 0.1960 to 0.2070 in, so #7 (75% thread) is inside and so is #5, the biggest. The table lists both for all 30 threads.
How much thread does class 2B allow?
At most about 83%. The least it allows is 53.0% to 67.2%, depending on the thread. Those figures come from the OSG and YG-1 limits and the formula in OSG's chart.
Is a 60% thread inside class 2B?
Only on 6 of the 30 inch threads here: #0-80, #2-56, #4-40, #5-40, #6-32 and #6-40. On the rest, a hole cut for exactly 60% is over the 2B maximum. A 60% thread may be strong enough, but it fails the class limit on those threads.
Does the standard tap drill meet class 2B?
On 27 of 30 inch threads. The exceptions are 9/16-18, 5/8-18 and 5/8-24. None of those three has a number, letter or 1/64 in drill inside the limits, so they need a metric drill.
Cite or reuse this data
Please quote these figures with a link to this page: TapDrillSize, "How much thread class 2B allows", https://tapdrillsize.com/class-2b-tap-drill-size/, published November 20, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.
Hole limits: class 2B limits from the OSG chart (the UNEF threads from the YG-1 chart) and class 6H limits from the Emuge chart. Thread percentages use the formula in the OSG tap drill chart, Vol 3 (2024). Drill sizes from Wikipedia: drill bit sizes. Published on November 20, 2026.