#8-32 Tap Drill Size
#8-32 tap drill size is a #29 drill, 0.136 in (3.45 mm). American Fastener, Little Machine Shop, Starrett and Bolt Depot print #29, and Emuge prints its size as a decimal, 0.1360 in. It sits inside the class 2B limits of 0.130 to 0.139 in from the OSG chart, but it leaves only about 69% thread, less than the 75% most charts aim for.
#8-32 is the coarse (UNC) thread on a #8 screw: 0.164 in across with 32 threads per inch. The reason its standard drill falls short of 75% is a gap in the number drill series. Three of the eight charts we read give a metric drill instead.
Why #8-32 has no 75% number drill
The OSG chart prints the exact hole for each thread percentage. On #8-32 the 75% hole is 0.1336 in, and no number drill is close: #30 is 0.1285 in and #29 is 0.136 in. The inch charts round up to #29 and accept about 69%.
| Thread | OSG hole | That hole against 2B |
|---|---|---|
| 80% | 0.1315 in | Inside |
| 75% | 0.1336 in | Inside |
| 70% | 0.1356 in | Inside |
| 65% | 0.1376 in | Inside |
| 60% | 0.1396 in | 0.0006 in over the max |
Class 2B on #8-32 runs from about 62% to 84% thread, so 69% is comfortably inside. A metric 3.4 mm drill, 0.1339 in, lands almost exactly on OSG's 75% hole if you want the fuller thread.
What eight charts print for #8-32
| Chart | Type | Drill | Size | Thread | Class 2B |
|---|---|---|---|---|---|
| American Fastener | Fastener supplier | #29 | 0.1360 in | 69% | Inside |
| Little Machine Shop | Tool supplier | #29 | 0.1360 in | 69% | Inside |
| Starrett | Tool maker | #29 | 0.1360 in | 69% | Inside |
| Bolt Depot | Fastener supplier | #29 | 0.1360 in | 69% | Inside |
| Emuge | Tap maker | 0.1360 in (#29) | 0.1360 in | 69% | Inside |
| Champion Cutting Tool | Tool maker | 3.4 mm or #29 | 0.1339 / 0.1360 in | 74% / 69% | Inside |
| Hartner (Gühring group) | Drill maker | 3.5 mm | 0.1378 in | 65% | Inside |
| Engineering Toolbox | Reference site | 3.5 mm | 0.1378 in | 65% | Inside |
Every drill in print passes 2B on this thread. Champion is the only chart to list 3.4 mm, and it lists it first, ahead of #29. Its own "probable percentage" figures for the two are 74% and 62%. The formula used on this page gives 74% and 69%, so on #29 Champion's figure is 7 points lower, and the chart does not say how it works its figures out. Hartner and Engineering Toolbox go the other way, to 3.5 mm, which leaves about 65% and is 0.0012 in under the 2B maximum.
Only one number drill passes
Diameters from Wikipedia, and thread percentages from OSG's formula: (0.164 − hole) / (1.299 / 32).
| Drill | Diameter | Thread left | Class 2B |
|---|---|---|---|
| #30 | 0.1285 in (3.26 mm) | 87% | Under the min by 0.0015 in |
| 3.3 mm | 0.1299 in | 84% | Under the min by 0.0001 in |
| 3.35 mm | 0.1319 in | 79% | Inside |
| 3.4 mm | 0.1339 in | 74% | Inside |
| 3.45 mm | 0.1358 in | 69% | Inside |
| #29 | 0.1360 in (3.45 mm) | 69% | Inside |
| 3.5 mm | 0.1378 in | 65% | Inside |
| #28 | 0.1405 in (3.57 mm) | 58% | Over the max by 0.0015 in |
| 9/64 in | 0.1406 in (3.57 mm) | 58% | Over the max by 0.0016 in |
#29 is the only number or fractional drill inside the band: #30 is just under it and #28 and 9/64 in are just over. If a #29 is missing from the drill index, use a metric drill, not a neighbouring number: 3.45 mm is only 0.0002 in smaller, and 3.4 or 3.5 mm also passes.
The M4 connection
M4, 4.00 mm across with a 0.7 mm pitch, is the metric size closest to #8-32 (4.17 mm, 0.79 mm pitch). The two do not share a standard drill: #29 is over the M4 class 6H maximum and the M4 drill, 3.3 mm, is just under the #8-32 2B minimum. A 3.4 mm drill passes both, about 74% thread here and about 66% in M4.
#8-32 roll and form taps
A forming tap needs a hole near 0.150 in. Balax prints a #25 (0.1495 in) or 3.8 mm (0.1496 in), Jarvis a #25 and Haas 3.8 mm, so the three agree within 0.0001 in.
FAQ
What is the #8-32 tap drill size?
#8-32 tap drill size is a #29 drill, 0.136 in (3.45 mm). It leaves about 69% thread, inside class 2B.
Why does #29 leave only 69% thread on #8-32?
No number drill lands near the 75% hole. OSG puts it at 0.1336 in, and the nearest number drills are #29 (0.136 in) and #30 (0.1285 in). #30 is under the 2B minimum, so the inch charts use #29.
What metric drill for #8-32?
3.4 mm (0.1339 in) is the closest to a 75% thread, at about 74%. Champion prints it. 3.5 mm also passes 2B.
Can I use #30 for #8-32?
No. A #30 (0.1285 in) is 0.0015 in under the class 2B minimum. It would leave about 87% thread and make the tap work hard.
What drill for an #8-32 roll tap?
A #25 (0.1495 in) or 3.8 mm. Balax gives both, Jarvis gives #25 and Haas gives 3.8 mm.
Related pages
Cite or reuse this data
Please quote these figures with a link to this page: TapDrillSize, "#8-32 tap drill size", https://tapdrillsize.com/8-32-tap-drill-size/, published November 5, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.
Chart drills from American Fastener, Little Machine Shop, Starrett, Bolt Depot, Emuge, Champion Cutting Tool, Hartner (Gühring group) and Engineering Toolbox. Class 2B limits, percentage holes and the thread percentage formula from the OSG chart. M4 class 6H limits from Emuge. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on November 5, 2026.