5/16-18 Tap Drill Size
5/16-18 tap drill size is a letter F drill, 0.257 in (6.53 mm). American Fastener, Little Machine Shop, Starrett, Bolt Depot and Champion Cutting Tool print letter F. It leaves about 77% thread and sits inside the class 2B limits of 0.252 to 0.265 in from the OSG chart.
5/16-18 is the coarse (UNC) 5/16 in thread, 18 threads per inch. Its nearest metric neighbour is M8, and and that is where two of the eight charts we read go wrong: beside letter F, they print drills that fit M8 but are too big for 5/16-18.
What eight charts print for 5/16-18
| Chart | Kind | Drill | Diameter | Thread | 2B |
|---|---|---|---|---|---|
| American Fastener | Fastener supplier | F | 0.2570 in | 77% | Inside |
| Little Machine Shop | Tool supplier | F | 0.2570 in | 77% | Inside |
| Starrett | Tool maker | F | 0.2570 in | 77% | Inside |
| Bolt Depot | Fastener supplier | F or 17/64 in | 0.2570 / 0.2656 in | 77% / 65% | Inside / 0.0006 in over |
| Champion Cutting Tool | Tool maker | F or G | 0.2570 / 0.2610 in | 77% / 71% | Inside |
| Emuge | Tap maker | 0.2610 in (letter G) | 0.2610 in | 71% | Inside |
| Hartner (Gühring group) | Drill maker | 6.6 mm | 0.2598 in | 73% | Inside |
| Engineering Toolbox | Reference site | 6.8 mm | 0.2677 in | 62% | 0.0027 in over |
Class 2B allows about 66% to 84% thread on 5/16-18. Bolt Depot's 17/64 in leaves 65% and Engineering Toolbox's 6.8 mm leaves 62%, so both fall just short. Champion's own "probable percentage" figures, 72% for F and 66% for G, sit about 5 points under the formula's 77% and 71%.
The M8 overlap that catches two charts
M8 x 1.25 is 8.00 mm across against 7.94 mm here, with a 1.25 mm pitch against 1.411 mm. The class 6H band for M8 runs from 6.647 to 6.912 mm; 2B for 5/16-18 runs from 6.401 to 6.731 mm. For M8 itself the charts disagree: Emuge and Hartner print 6.8 mm, Starrett and Champion 6.7 mm, and Bolt Depot 6.9 mm. Engineering Toolbox's 6.8 mm for 5/16-18 is that M8 figure, and Bolt Depot's 17/64 in, like letter H, sits inside M8 6H too. All three are outside 2B for 5/16-18.
Going the other way, letter F is 0.119 mm under the M8 minimum. The bands overlap only from 6.647 to 6.731 mm, and the one drill in that overlap is 6.7 mm, the M8 figure Starrett and Champion print. It leaves about 68% thread here.
Every drill near letter F
Diameters from Wikipedia, thread percentage from the OSG formula: (0.3125 − hole) / (1.299 / 18).
| Drill | Diameter | Thread left | Class 2B |
|---|---|---|---|
| Letter E | 0.2500 in (6.35 mm) | 87% | Under the min by 0.0020 in |
| 6.45 mm | 0.2539 in | 81% | Inside |
| 6.5 mm | 0.2559 in | 78% | Inside |
| Letter F | 0.2570 in (6.53 mm) | 77% | Inside |
| 6.55 mm | 0.2579 in | 76% | Inside |
| 6.6 mm | 0.2598 in | 73% | Inside |
| Letter G | 0.2610 in (6.63 mm) | 71% | Inside |
| 6.65 mm | 0.2618 in | 70% | Inside |
| 6.7 mm | 0.2638 in | 68% | Inside |
| 17/64 in | 0.2656 in (6.75 mm) | 65% | Over the max by 0.0006 in |
| Letter H | 0.2660 in (6.76 mm) | 64% | Over the max by 0.0010 in |
| 6.8 mm | 0.2677 in | 62% | Over the max by 0.0027 in |
Two letter drills pass, F and G, and no fractional drill does. In tough metal, letter G or 6.6 mm takes load off the tap and keeps 2B.
Helicoil (STI) drill for 5/16-18
For once the two insert charts we compared both land inside. The ASME B18.29.1 range for a 5/16-18 STI hole is 0.3245 to 0.3342 in (AmesWeb). AmesWeb suggests 21/64 in (0.3281 in); Albany County Fasteners, wrong on several other sizes, prints letter Q (0.332 in), nearer the top of the range. Hartner's insert table gives a third answer, 8.40 mm (0.3307 in), also inside. Any of the three works.
5/16-18 roll and form taps
Balax prints 7.25 mm, and Jarvis and Haas 7.3 mm, for a 5/16-18 forming tap. That is 0.7 to 0.8 mm more than letter F.
FAQ
What is the 5/16-18 tap drill size?
5/16-18 tap drill size is a letter F drill, 0.257 in (6.53 mm), for about 77% thread inside class 2B.
Is 17/64 OK for 5/16-18?
Not for class 2B. Bolt Depot lists 17/64 in, but at 0.2656 in it is 0.0006 in over the 2B maximum of 0.265 in.
What metric drill for 5/16-18?
6.5 mm or 6.6 mm. Hartner prints 6.6 mm (about 73% thread). Engineering Toolbox prints 6.8 mm, which is 0.0027 in over the 2B maximum.
Can I use the M8 drill for 5/16-18?
It depends which M8 drill. 6.8 mm, which Emuge and Hartner print for M8, is 0.0027 in over the 5/16-18 2B maximum. 6.7 mm, which Starrett and Champion print for M8, is inside both.
What drill for a 5/16-18 Helicoil?
21/64 in (0.3281 in), per AmesWeb's ASME B18.29.1 table. Albany County Fasteners prints letter Q (0.332 in), which is also inside the STI limits.
Related pages
Cite or reuse this data
Please quote these figures with a link to this page: TapDrillSize, "5/16-18 tap drill size", https://tapdrillsize.com/5-16-18-tap-drill-size/, published November 15, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.
Chart drills from American Fastener, Little Machine Shop, Starrett, Bolt Depot, Champion Cutting Tool, Emuge, Hartner (Gühring group) and Engineering Toolbox. Class 2B limits and the thread percentage formula from the OSG chart; M8 class 6H limits from Emuge. STI limits and drills from AmesWeb and Albany County Fasteners. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on November 15, 2026.