9/16-18 Tap Drill Size
9/16-18 tap drill size is 33/64 in on most inch charts, but that drill is 0.0006 in over the class 2B hole limit. A 12.9 mm drill (0.5079 in) passes, with about 76% thread inside the 2B limits of 0.502 to 0.515 in from the OSG chart.
9/16-18 is the fine (UNF) 9/16 in thread, 18 threads per inch. Like 5/8-18, it is a size where every inch-only chart we read gives a drill outside 2B. Here the inch charts miss by more, 0.0006 in against 0.0001 in, and the table on Wikipedia, which cites Machinery's Handbook, gives a drill that fails, as it does on 5/8-18.
What the charts print for 9/16-18
| Source | Kind | Drill | Diameter | Thread | 2B |
|---|---|---|---|---|---|
| American Fastener | Fastener supplier | 33/64 in | 0.5156 in | 65% | 0.0006 in over |
| Little Machine Shop | Tool supplier | 33/64 in | 0.5156 in | 65% | 0.0006 in over |
| Starrett | Tool maker | 33/64 in | 0.5156 in | 65% | 0.0006 in over |
| Bolt Depot | Fastener supplier | 33/64 in | 0.5156 in | 65% | 0.0006 in over |
| Champion Cutting Tool | Tool maker | 1/2 in, then 33/64 in | 0.5000 / 0.5156 in | 87% / 65% | 1/2 0.0020 in under, 33/64 0.0006 in over |
| Wikipedia (Machinery's Handbook) | Reference | 1/2 in | 0.5000 in | 87% | 0.0020 in under |
| Engineering Toolbox | Reference site | 12.9 mm | 0.5079 in | 76% | Inside |
| Hartner (Gühring group) | Drill maker | 12.9 mm | 0.5079 in | 76% | Inside |
| Emuge | Tap maker | 0.5118 in (13.0 mm) | 0.5118 in | 70% | Inside |
Six of the nine sources give only drills outside 2B: four print a drill that is too big, Wikipedia one that is too small, and Champion one of each. Champion's own "probable percentage" for its two drills is 82% and 60%. Only the three charts that give a metric-size drill land inside the band.
9/16-18 drills from 1/2 in to 13.1 mm
Thread left is (0.5625 − hole) / (1.299 / 18). Class 2B spans about 66% to 84% thread. Diameters from Wikipedia.
| Drill | Diameter | Thread left | Class 2B |
|---|---|---|---|
| 1/2 in | 0.5000 in (12.70 mm) | 87% | Under the min by 0.0020 in |
| 12.8 mm | 0.5039 in | 81% | Inside |
| 12.9 mm | 0.5079 in | 76% | Inside |
| 13.0 mm | 0.5118 in | 70% | Inside |
| 13.05 mm | 0.5138 in | 68% | Inside |
| 33/64 in | 0.5156 in (13.10 mm) | 65% | Over the max by 0.0006 in |
| 13.1 mm | 0.5157 in | 65% | Over the max by 0.0007 in |
12.8 to 13.05 mm all pass. 13.1 mm is just over, by 0.0007 in, almost the same hole as 33/64 in.
No inch drill fits 9/16-18
The band, 0.502 to 0.515 in, falls between 1/2 in and 33/64 in, two fractional drills 1/64 in (0.0156 in) apart, so neither lands inside. Number drills stop well short of this size, and letter drills stop at Z, 0.413 in. That leaves an inch shop with a choice: 33/64 in, which works as a thread at about 65% where no class is called for, or a 12.9 or 13.0 mm drill where the drawing says 2B.
9/16-18 UNJF
For the rounded-root UNJF form, Hartner gives 13.00 mm, with class 3B limits of 12.913 to 13.122 mm. 13.0 mm is inside both that band and UNF 2B. 33/64 in (13.097 mm) is inside UNJF only, and 12.9 mm is 0.013 mm under the UNJF minimum.
9/16-18 Helicoil and roll taps
AmesWeb's ASME B18.29.1 table gives an STI hole of 0.5745 to 0.5826 in and suggests 37/64 in (0.5781 in). Hartner's insert table gives 14.70 mm (0.5787 in), with limits of 14.592 to 14.798 mm, the same range. The two agree. The Albany County Fasteners chart we compare on other sizes has no 9/16-18 row.
For a forming tap, Balax gives 0.536 in, Jarvis a 0.5380 in hole and Haas 13.6 mm (0.5354 in).
FAQ
What is the 9/16-18 tap drill size?
9/16-18 tap drill size is 33/64 in on most inch charts, but 33/64 in (0.5156 in) is 0.0006 in over the class 2B maximum. 12.9 mm (0.5079 in) passes, at about 76% thread.
Is 1/2 in OK for 9/16-18?
No. 1/2 in is Champion's first choice and the drill in Wikipedia's Unified thread table, but it is 0.0020 in under the 2B minimum of 0.502 in.
Is there an inch drill for 9/16-18?
Not a standard one. 1/2 in is too small and 33/64 in too big, and letter drills stop at Z (0.413 in). Use a metric drill from 12.8 to 13.05 mm.
What drill for a 9/16-18 Helicoil?
37/64 in (0.5781 in), per AmesWeb, or 14.70 mm per Hartner. Both fit the STI hole of 0.5745 to 0.5826 in.
What drill for 9/16-18 UNJF?
Hartner gives 13.00 mm, with limits of 12.913 to 13.122 mm. 13.0 mm also passes UNF 2B, so it fits both.
Related pages
Cite or reuse this data
Please quote these figures with a link to this page: TapDrillSize, "9/16-18 tap drill size", https://tapdrillsize.com/9-16-18-tap-drill-size/, published December 13, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.
Chart drills from American Fastener, Little Machine Shop, Starrett, Bolt Depot, Champion Cutting Tool, Emuge, Hartner (Gühring group) and Engineering Toolbox, plus the preferred drill in Wikipedia's Unified thread table. Class 2B limits and the thread percentage formula from the OSG chart. UNJF and insert limits from Hartner (Gühring group). STI limits and drill from AmesWeb. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on December 13, 2026.