3/4-16 Tap Drill Size
3/4-16 tap drill size is 11/16 in (0.6875 in, 17.46 mm). It leaves about 77% thread inside the class 2B hole limits of 0.682 to 0.696 in from the OSG chart. The metric charts print 17.5 mm, which also passes.
3/4-16 is the fine (UNF) 3/4 in thread, 16 threads per inch. Its metric tap drill, 17.5 mm, is also the drill M20 takes.
3/4-16: 11/16 in or 17.5 mm
| Chart | Kind | Drill | Diameter | Thread | 2B |
|---|---|---|---|---|---|
| American Fastener | Fastener supplier | 11/16 in | 0.6875 in | 77% | Inside |
| Little Machine Shop | Tool supplier | 11/16 in | 0.6875 in | 77% | Inside |
| Starrett | Tool maker | 11/16 in | 0.6875 in | 77% | Inside |
| Bolt Depot | Fastener supplier | 11/16 in | 0.6875 in | 77% | Inside |
| Champion Cutting Tool | Tool maker | 11/16 in or 17.5 mm | 0.6875 / 0.6890 in | 77% / 75% | Inside |
| Emuge | Tap maker | 0.6890 in (17.5 mm) | 0.6890 in | 75% | Inside |
| Hartner (Gühring group) | Drill maker | 17.5 mm | 0.6890 in | 75% | Inside |
| Engineering Toolbox | Reference site | 17.5 mm | 0.6890 in | 75% | Inside |
All eight charts pass, split between 11/16 in and 17.5 mm (Emuge prints it as 0.6890 in), which are 0.0015 in apart. Champion lists both and rates them at a "probable" 72% and 70%, about 5 points under the OSG formula.
3/4-16 drills from 17.3 to 17.7 mm
Thread left is (0.750 − hole) / (1.299 / 16). Class 2B on 3/4-16 spans about 67% to 84% thread, a band 0.014 in wide. Diameters from Wikipedia.
| Drill | Diameter | Thread left | Class 2B |
|---|---|---|---|
| 17.3 mm | 0.6811 in | 85% | Under the min by 0.0009 in |
| 17.35 mm | 0.6831 in | 82% | Inside |
| 17.4 mm | 0.6850 in | 80% | Inside |
| 11/16 in | 0.6875 in (17.46 mm) | 77% | Inside |
| 17.5 mm | 0.6890 in | 75% | Inside |
| 17.6 mm | 0.6929 in | 70% | Inside |
| 17.65 mm | 0.6949 in | 68% | Inside |
| 17.7 mm | 0.6969 in | 65% | Over the max by 0.0009 in |
11/16 in is the only fractional drill in the band; 43/64 in is too small and 45/64 in too big. In metric, 17.35 to 17.65 mm pass, and 17.3 and 17.7 mm both miss by 0.0009 in, one at each end.
3/4-16 and the M20 drill
The M20 6H band is 17.294 to 17.744 mm. The 3/4-16 2B band, 0.682 to 0.696 in, is 17.323 to 17.678 mm, so it sits entirely inside the M20 band. Any drill that passes 3/4-16 also passes M20, and 17.5 mm is the standard for both. The reverse doesn't hold at the edges: 17.3 mm and 17.7 mm pass M20 but miss 3/4-16. The screws don't swap. 3/4 in is 19.05 mm against 20 mm, and 16 threads per inch is a 1.588 mm pitch against 2.5 mm for coarse M20.
3/4-16 Helicoil and roll taps
AmesWeb's ASME B18.29.1 table gives an STI minor diameter of 0.7635 to 0.772 in and suggests 49/64 in (0.7656 in). Albany County Fasteners prints 23/32 in (0.7188 in) for the same insert, 0.0447 in under the minimum, so the two sources disagree by more than a millimetre. Hartner's insert table, which we use as a third check, stops at 5/8-18. Only AmesWeb publishes hole limits for this size. Its 49/64 in fits them and Albany's 23/32 in does not, so the two sources disagree.
Oddly, Albany's 23/32 in is the drill Balax gives for a 3/4-16 forming tap. Haas gives 18.3 mm (0.7205 in) for the same job, and Jarvis a 0.7224 in hole.
FAQ
What is the 3/4-16 tap drill size?
3/4-16 tap drill size is 11/16 in (0.6875 in, 17.46 mm), for about 77% thread inside class 2B.
What metric drill for 3/4-16?
17.5 mm leaves about 75%. Four of the eight charts give it, Emuge as the decimal 0.6890 in. 17.35 to 17.65 mm all pass 2B.
Is the 3/4-16 drill the same as the M20 drill?
Yes, 17.5 mm is the standard drill for both. In fact every hole inside 3/4-16 class 2B is also inside the M20 6H band. The threads are different and do not fit each other.
What drill for a 3/4-16 Helicoil?
49/64 in (0.7656 in), per AmesWeb, for an STI hole of 0.7635 to 0.772 in. Albany County Fasteners prints 23/32 in, which is 0.0447 in too small.
What drill for a 3/4-16 roll tap?
Balax gives 23/32 in (0.7188 in), Haas 18.3 mm and Jarvis a 0.7224 in hole.
Related pages
Cite or reuse this data
Please quote these figures with a link to this page: TapDrillSize, "3/4-16 tap drill size", https://tapdrillsize.com/3-4-16-tap-drill-size/, published December 9, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.
Chart drills from American Fastener, Little Machine Shop, Starrett, Bolt Depot, Champion Cutting Tool, Emuge, Hartner (Gühring group) and Engineering Toolbox. Class 2B limits and the thread percentage formula from the OSG chart. M20 6H limits from Emuge and Hartner (Gühring group). STI limits and drills from AmesWeb and Albany County Fasteners. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on December 9, 2026.