#10-32 Tap Drill Size
#10-32 tap drill size is a #21 drill, 0.159 in (4.04 mm). American Fastener, Little Machine Shop, Starrett and Bolt Depot all print #21. It leaves about 76% of a full thread and sits inside the class 2B limits of 0.156 to 0.164 in from the OSG chart.
#10-32 is the fine (UNF) thread on a #10 screw, 0.190 in across with 32 threads per inch. Its 2B band is only 0.008 in wide, yet the eight charts we read give three different drills for it, and all three land inside.
Eight charts, three answers, all inside 2B
| Chart | Publisher | Drill printed | Diameter | Thread | 2B |
|---|---|---|---|---|---|
| American Fastener | Fastener supplier | #21 | 0.1590 in | 76% | Inside |
| Little Machine Shop | Tool supplier | #21 | 0.1590 in | 76% | Inside |
| Starrett | Tool maker | #21 | 0.1590 in | 76% | Inside |
| Bolt Depot | Fastener supplier | #21 or 5/32 in | 0.1590 / 0.1563 in | 76% / 83% | Inside |
| Champion Cutting Tool | Tool maker | 5/32 in or #21 | 0.1563 / 0.1590 in | 83% / 76% | Inside |
| Emuge | Tap maker | 0.1614 in (4.1 mm) | 0.1614 in | 70% | Inside |
| Hartner (Gühring group) | Drill maker | 4.1 mm | 0.1614 in | 70% | Inside |
| Engineering Toolbox | Reference site | 4.1 mm | 0.1614 in | 70% | Inside |
The three answers come from three drill series. The four US fastener and tool charts use the number drill, #21. Bolt Depot and Champion also give the fractional 5/32 in, and Champion lists it first, with its own "probable percentage" of 75% for 5/32 in and 68% for #21. The formula on this page gives 83% and 76%, so Champion's figures run about 8 points lower. Hartner and Engineering Toolbox print 4.1 mm, and Emuge prints 0.1614 in, the same hole.
5/32 in is the tightest of the three: it clears the 2B minimum by only 0.00025 in. A worn drill that cuts undersize can take it out of class, so #21 or 4.1 mm is the safer pick where the hole will be gauged.
Every drill near #21
Diameters from Wikipedia. Thread percentage is (0.190 − hole) / (1.299 / 32), the OSG formula.
| Drill | Diameter | Thread left | Class 2B |
|---|---|---|---|
| #23 | 0.1540 in (3.91 mm) | 89% | Under the min by 0.0020 in |
| 3.95 mm | 0.1555 in | 85% | Under the min by 0.0005 in |
| 5/32 in | 0.1563 in (3.97 mm) | 83% | Inside |
| #22 | 0.1570 in (3.99 mm) | 81% | Inside |
| 4.0 mm | 0.1575 in | 80% | Inside |
| #21 | 0.1590 in (4.04 mm) | 76% | Inside |
| 4.05 mm | 0.1594 in | 75% | Inside |
| #20 | 0.1610 in (4.09 mm) | 71% | Inside |
| 4.1 mm | 0.1614 in | 70% | Inside |
| 4.15 mm | 0.1634 in | 66% | Inside |
| 4.2 mm | 0.1654 in | 61% | Over the max by 0.0014 in |
| #19 | 0.1660 in (4.22 mm) | 59% | Over the max by 0.0020 in |
Eight drills pass, from 5/32 in to 4.15 mm. 4.05 mm is the closest metric drill to #21. For tougher metal, #20 or 4.1 mm takes some load off the tap and stays well inside the band.
Where you find #10-32
- Equipment racks. Threaded 19-inch rack rails have round holes tapped for 10-32 UNF or 10-24 UNC screws (Wikipedia). Square-hole rails take cage nuts instead. Wikipedia gives 10-32 as the usual cage nut thread in the US, and M5 or M6 elsewhere.
- Small pneumatic fittings. Push-in fittings such as Festo's QSMK series use a 10-32 UNF male port, here for 5/32 in tubing.
When you tap a port or a rail for these parts, it is the same #10-32 thread and the same #21 drill.
#10-32, #10-24 and M5
| Thread | Diameter | Pitch | Standard drill |
|---|---|---|---|
| #10-32 UNF | 4.83 mm | 0.794 mm (32 TPI) | #21 |
| #10-24 UNC | 4.83 mm | 1.058 mm (24 TPI) | #25 |
| M5 x 0.8 | 5.00 mm | 0.800 mm | 4.2 mm |
#10-24 is the coarse thread on the same #10 screw, so the diameter alone does not tell you the drill. M5 has almost the same pitch but is 0.17 mm bigger, and only a 4.15 mm drill, from a 0.05 mm set, passes the limits for both.
#10-32 roll and form taps
The forming tap hole is near 0.176 in, with Haas a little smaller. Balax gives a #16 (0.177 in) or 0.176 in, Jarvis gives the hole itself, 0.1763 in, without naming a drill, and Haas gives 4.4 mm (0.1732 in).
FAQ
What is the #10-32 tap drill size?
#10-32 tap drill size is a #21 drill, 0.159 in (4.04 mm), for about 76% thread inside class 2B.
Is 5/32 OK for #10-32?
Yes, but only just. 5/32 in (0.15625 in) is 0.00025 in above the class 2B minimum and leaves about 83% thread. Bolt Depot and Champion print it.
What metric drill for #10-32?
4.1 mm, as Hartner and Engineering Toolbox print (Emuge gives the same hole as 0.1614 in). It leaves about 70% thread. 4.05 mm is closest to #21, at about 75%.
Is #10-32 the same drill as #10-24?
No. #10-24 is the coarse thread on the same screw and takes a #25 drill. #10-32 is the fine thread and takes #21.
What thread are threaded rack rails?
Wikipedia lists 10-32 UNF and 10-24 UNC for tapped 19-inch rack rails, so check the screw before you retap one.
Related pages
Cite or reuse this data
Please quote these figures with a link to this page: TapDrillSize, "#10-32 tap drill size", https://tapdrillsize.com/10-32-tap-drill-size/, published November 7, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.
Chart drills from American Fastener, Little Machine Shop, Starrett, Bolt Depot, Champion Cutting Tool, Emuge, Hartner (Gühring group) and Engineering Toolbox. Class 2B limits and the thread percentage formula from the OSG chart. Rack rail and cage nut threads from Wikipedia and Wikipedia, fitting port from RS Components. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on November 7, 2026.