5/8-18 Tap Drill Size
5/8-18 tap drill size is 37/64 in on most inch charts, but that drill is 0.0001 in over the class 2B hole limit. The drill that passes is 14.5 mm (0.5709 in), which leaves about 75% thread inside the 2B limits of 0.565 to 0.578 in from the OSG chart.
5/8-18 is the fine (UNF) 5/8 in thread, 18 threads per inch. It is one of two sizes on this site, with 9/16-18, where all four charts that give only fractional, letter or number drills for inch threads (American Fastener, Little Machine Shop, Starrett and Bolt Depot) print a drill outside 2B. The miss is tiny, 37/64 in is 0.578125 in against a 0.578 in maximum, but it is the wrong side of the line, and the sources disagree. We show both.
Five of eight charts print a drill outside 2B
| Chart | Kind | Drill | Diameter | Thread | 2B |
|---|---|---|---|---|---|
| American Fastener | Fastener supplier | 37/64 in | 0.5781 in | 65% | 0.0001 in over |
| Little Machine Shop | Tool supplier | 37/64 in | 0.5781 in | 65% | 0.0001 in over |
| Starrett | Tool maker | 37/64 in | 0.5781 in | 65% | 0.0001 in over |
| Bolt Depot | Fastener supplier | 37/64 in | 0.5781 in | 65% | 0.0001 in over |
| Champion Cutting Tool | Tool maker | 9/16 in, then 37/64 in | 0.5625 / 0.5781 in | 87% / 65% | 9/16 0.0025 in under, 37/64 0.0001 in over |
| Emuge | Tap maker | 0.5709 in (14.5 mm) | 0.5709 in | 75% | Inside |
| Hartner (Gühring group) | Drill maker | 14.5 mm | 0.5709 in | 75% | Inside |
| Engineering Toolbox | Reference site | 14.5 mm | 0.5709 in | 75% | Inside |
The inch charts are stuck between two fractional drills. 9/16 in is too small and 37/64 in is a hair too big, and the 64ths step from one to the other, 0.0156 in, is wider than the whole 2B band of 0.013 in. Champion lists both, and its own "probable percentage" puts them at 82% and 60% thread. The three charts that give 14.5 mm, Emuge as the decimal 0.5709 in, land near the middle of the band.
5/8-18 drills from 9/16 in to 14.7 mm
Thread left is (0.625 − hole) / (1.299 / 18). Class 2B spans about 65% to 83% thread. Diameters from Wikipedia.
| Drill | Diameter | Thread left | Class 2B |
|---|---|---|---|
| 9/16 in | 0.5625 in (14.29 mm) | 87% | Under the min by 0.0025 in |
| 14.3 mm | 0.5630 in | 86% | Under the min by 0.0020 in |
| 14.4 mm | 0.5669 in | 80% | Inside |
| 14.5 mm | 0.5709 in | 75% | Inside |
| 14.6 mm | 0.5748 in | 70% | Inside |
| 14.65 mm | 0.5768 in | 67% | Inside |
| 37/64 in | 0.5781 in (14.68 mm) | 65% | Over the max by 0.0001 in |
| 14.7 mm | 0.5787 in | 64% | Over the max by 0.0007 in |
No fractional inch drill fits; a metric set does, from 14.4 to 14.65 mm. If you only have inch drills and the drawing names no class, 37/64 in will make a working thread at about 65%. If it says 2B, use 14.5 mm.
5/8-18 UNJF and M16 x 1.5
For the rounded-root UNJF form, Hartner gives 14.60 mm, with class 3B limits of 14.501 to 14.702 mm. Here 37/64 in (14.684 mm) is inside, and 14.5 mm is 0.001 mm under the UNJF minimum. 14.6 and 14.65 mm are the drills in the table that fit both UNF 2B and UNJF, at about 70% and 67% thread.
The 2B band in millimetres, 14.351 to 14.681 mm, is almost the same as the 6H band Hartner gives for M16 x 1.5, 14.376 to 14.676 mm, and Hartner's M16 x 1.5 drill is 14.5 mm too. The pitches differ, 1.411 mm against 1.5 mm, so the screws are not interchangeable.
5/8-18 Helicoil drill
AmesWeb's ASME B18.29.1 table gives an STI hole of 0.637 to 0.6451 in and suggests 41/64 in (0.6406 in). Hartner's insert table gives 16.25 mm (0.6398 in), with limits of 16.180 to 16.386 mm. Those agree. Albany County Fasteners prints 19/32 in (0.5938 in), 0.0432 in under the STI minimum. Albany's drills for 1/4-28, 5/16-24, 7/16-20 and 1/2-20 are also under AmesWeb's minimum.
5/8-18 roll and form taps
Balax gives 0.598 in, Jarvis a 0.6004 in hole and Haas 15.2 mm (0.5984 in).
FAQ
What is the 5/8-18 tap drill size?
5/8-18 tap drill size is 37/64 in on most inch charts, but 37/64 in (0.5781 in) is 0.0001 in over the class 2B maximum. 14.5 mm (0.5709 in) is inside, at about 75% thread.
Is 37/64 OK for 5/8-18?
Only where no thread class is called for. It leaves about 65% thread and is 0.0001 in over the 2B maximum of 0.578 in; any drill that cuts oversize takes it further out.
Is 9/16 OK for 5/8-18?
No. 9/16 in (0.5625 in) is Champion's first choice, but it is 0.0025 in under the 2B minimum and would cut about 87% thread.
What drill for a 5/8-18 Helicoil?
41/64 in (0.6406 in), per AmesWeb, or 16.25 mm per Hartner. Albany County Fasteners prints 19/32 in, 0.0432 in under the STI minimum.
Is 5/8-18 the same drill as M16 x 1.5?
Yes, 14.5 mm. Hartner gives it for M16 x 1.5 with 6H limits of 14.376 to 14.676 mm, almost the same range as 5/8-18 2B.
Related pages
Cite or reuse this data
Please quote these figures with a link to this page: TapDrillSize, "5/8-18 tap drill size", https://tapdrillsize.com/5-8-18-tap-drill-size/, published December 10, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.
Chart drills from American Fastener, Little Machine Shop, Starrett, Bolt Depot, Champion Cutting Tool, Emuge, Hartner (Gühring group) and Engineering Toolbox. Class 2B limits and the thread percentage formula from the OSG chart. UNJF, M16 x 1.5 and insert limits from Hartner (Gühring group). STI limits and drills from AmesWeb and Albany County Fasteners. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on December 10, 2026.