7/8-14 Tap Drill Size
7/8-14 tap drill size is 13/16 in (0.8125 in, 20.64 mm). It leaves about 67% thread inside the class 2B hole limits of 0.798 to 0.814 in from the OSG chart. Hartner and Engineering Toolbox print 20.4 mm and Emuge 0.8071 in (20.5 mm), which leave more thread and also pass.
7/8-14 is the fine (UNF) 7/8 in thread, 14 threads per inch. The inch charts split here between a drill that passes, 13/16 in, and one that does not, 51/64 in. They are 1/64 in apart. The 2B band starts 0.0011 in above 51/64 in and takes in 13/16 in.
7/8-14: 13/16 in or 51/64 in
| Source | Kind | Drill | Diameter | Thread | 2B |
|---|---|---|---|---|---|
| American Fastener | Fastener supplier | 13/16 in | 0.8125 in | 67% | Inside |
| Little Machine Shop | Tool supplier | 13/16 in | 0.8125 in | 67% | Inside |
| Starrett | Tool maker | 13/16 in | 0.8125 in | 67% | Inside |
| Champion Cutting Tool | Tool maker | 51/64 in, then 13/16 in | 0.7969 / 0.8125 in | 84% / 67% | 51/64 0.0011 in under, 13/16 inside |
| Wikipedia (Machinery's Handbook) | Reference | 51/64 in | 0.7969 in | 84% | 0.0011 in under |
| Hartner (Gühring group) | Drill maker | 20.4 mm | 0.8031 in | 77% | Inside |
| Engineering Toolbox | Reference site | 20.4 mm | 0.8031 in | 77% | Inside |
| Emuge | Tap maker | 0.8071 in (20.5 mm) | 0.8071 in | 73% | Inside |
Bolt Depot's chart has no 7/8-14 row. Champion leads with 51/64 in, which it rates at a "probable" 79% thread and the OSG formula at 84%, and Wikipedia's Unified thread table, citing Machinery's Handbook, gives the same drill. Both are 0.0011 in under the 2B minimum.
7/8-14 drills from 20.2 to 20.7 mm
Thread left is (0.875 − hole) / (1.299 / 14). Class 2B spans about 66% to 83% thread. Diameters from Wikipedia.
| Drill | Diameter | Thread left | Class 2B |
|---|---|---|---|
| 20.2 mm | 0.7953 in | 86% | Under the min by 0.0027 in |
| 51/64 in | 0.7969 in (20.24 mm) | 84% | Under the min by 0.0011 in |
| 20.3 mm | 0.7992 in | 82% | Inside |
| 20.4 mm | 0.8031 in | 77% | Inside |
| 20.5 mm | 0.8071 in | 73% | Inside |
| 20.6 mm | 0.8110 in | 69% | Inside |
| 13/16 in | 0.8125 in (20.64 mm) | 67% | Inside |
| 20.7 mm | 0.8150 in | 65% | Over the max by 0.0010 in |
13/16 in passes near the loose end, at about 67%. A metric drill gives more thread: 20.4 mm leaves about 77% and 20.5 mm about 73%.
Two slightly different maximums
The sources don't quite agree on the top of the band. OSG gives a 2B maximum of 0.814 in (20.676 mm). Hartner's chart gives 20.269 to 20.650 mm, a maximum of 0.8130 in. 13/16 in is inside both, by 0.0015 in against OSG and 0.0005 in against Hartner. 20.6 mm is inside both too; 20.7 mm is over both.
7/8-14 and M22 x 1.5
7/8 in is 22.225 mm, close to M22. Hartner gives M22 x 1.5 a 20.5 mm drill and 6H limits of 20.376 to 20.676 mm, which fall inside 7/8-14 2B by OSG's figures. So 20.5 mm serves both. The pitches differ, 1.814 mm against 1.5 mm, so the screws don't fit each other. For coarse M22 see M22.
7/8-14 Helicoil and roll taps
AmesWeb's ASME B18.29.1 table gives an STI minor diameter of 0.8905 to 0.8994 in and suggests 57/64 in (0.8906 in), only 0.0001 in above the minimum. A drill that cuts even slightly under size would leave the hole out of range. Hartner's UNF insert table stops at 5/8-18, so we have no second source here.
For a forming tap, Balax gives 27/32 in (0.8438 in) and Haas 21.4 mm (0.8425 in). Jarvis's chart has no 7/8-14 drill.
FAQ
What is the 7/8-14 tap drill size?
7/8-14 tap drill size is 13/16 in (0.8125 in, 20.64 mm), for about 67% thread inside class 2B.
What metric drill for 7/8-14?
20.4 mm, which Hartner and Engineering Toolbox print, leaves about 77%. 20.5 mm, which matches Emuge's 0.8071 in, about 73%. 20.3 to 20.6 mm all pass 2B.
Is 51/64 OK for 7/8-14?
No. It is Champion's first choice and the drill in Wikipedia's Unified thread table, but 51/64 in (0.7969 in) is 0.0011 in under the 2B minimum.
What drill for a 7/8-14 Helicoil?
57/64 in (0.8906 in), per AmesWeb, for an STI hole of 0.8905 to 0.8994 in. It is inside by only 0.0001 in.
Does the M22 x 1.5 drill fit 7/8-14?
Yes. Hartner's M22 x 1.5 drill is 20.5 mm, inside 7/8-14 2B. The screws differ: 14 threads per inch is a 1.814 mm pitch.
Related pages
Cite or reuse this data
Please quote these figures with a link to this page: TapDrillSize, "7/8-14 tap drill size", https://tapdrillsize.com/7-8-14-tap-drill-size/, published December 15, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.
Chart drills from American Fastener, Little Machine Shop, Starrett, Champion Cutting Tool, Emuge, Hartner (Gühring group) and Engineering Toolbox, plus the preferred drill in Wikipedia's Unified thread table; Bolt Depot has no 7/8-14 row. Class 2B limits and the thread percentage formula from the OSG chart; Hartner's own limits and M22 x 1.5 row from Hartner (Gühring group). STI limits and drill from AmesWeb. Form tap drills from Balax and Haas. Drill diameters from Wikipedia. Published on December 15, 2026.