7/16-14 Tap Drill Size
7/16-14 tap drill size is letter U (0.368 in, 9.35 mm). Seven of the eight charts we compared give U or a metric drill close to it, and U leaves about 75% thread inside the class 2B hole limits of 0.360 to 0.376 in from the OSG chart.
7/16-14 is the coarse (UNC) 7/16 in thread, with 14 threads per inch. It is an awkward size in metric shops, because 7/16 in is 11.11 mm, between M10 and M12. Nothing metric screws into it, so the drill has to be chosen for the inch thread alone.
What the charts print for 7/16-14
| Chart | Kind | Drill | Diameter | Thread | 2B |
|---|---|---|---|---|---|
| American Fastener | Fastener supplier | U | 0.3680 in | 75% | Inside |
| Little Machine Shop | Tool supplier | U | 0.3680 in | 75% | Inside |
| Starrett | Tool maker | U | 0.3680 in | 75% | Inside |
| Champion Cutting Tool | Tool maker | U | 0.3680 in | 75% | Inside |
| Emuge | Tap maker | 0.3680 in (U) | 0.3680 in | 75% | Inside |
| Bolt Depot | Fastener supplier | U or 23/64 in | 0.3680 / 0.3594 in | 75% / 84% | U inside, 23/64 in 0.0006 in under |
| Hartner (Gühring group) | Drill maker | 9.4 mm | 0.3701 in | 73% | Inside |
| Engineering Toolbox | Reference site | 9.65 mm | 0.3799 in | 62% | 0.0039 in over |
Two charts miss, in opposite directions. Bolt Depot's second choice, 23/64 in, is a hair small: it would cut about 84% thread and fails a 2B minor-diameter check by 0.0006 in. Engineering Toolbox's 9.65 mm goes the other way and leaves only about 62% thread, 0.0039 in over the maximum. Champion's own "probable percentage" for U is 75%, the same as the OSG formula gives.
Drills from T to 9.65 mm
Thread left is (0.4375 − hole) / (1.299 / 14). On 7/16-14, class 2B runs from about 66% to 84% thread. Diameters from Wikipedia.
| Drill | Diameter | Thread left | Class 2B |
|---|---|---|---|
| Letter T | 0.3580 in (9.09 mm) | 86% | Under the min by 0.0020 in |
| 23/64 in | 0.3594 in (9.13 mm) | 84% | Under the min by 0.0006 in |
| 9.2 mm | 0.3622 in | 81% | Inside |
| 9.3 mm | 0.3661 in | 77% | Inside |
| Letter U | 0.3680 in (9.35 mm) | 75% | Inside |
| 9.4 mm | 0.3701 in | 73% | Inside |
| 9.5 mm | 0.3740 in | 68% | Inside |
| 3/8 in | 0.3750 in (9.52 mm) | 67% | Inside |
| 9.55 mm | 0.3760 in | 66% | Inside |
| Letter V | 0.3770 in (9.58 mm) | 65% | Over the max by 0.0010 in |
| 9.65 mm | 0.3799 in | 62% | Over the max by 0.0039 in |
If you don't own a U, a plain 3/8 in bit from a fractional set works. It sits near the top of the band at about 67% and makes the tap easier to turn in tough steel. Letter V, one size up, is just too big.
7/16-14 UNC and UNJC
UNJC is the same pitch and major diameter with a rounded root, used for aerospace fasteners, and its internal thread needs a bigger minor diameter. Hartner's chart lists 7/16-14 UNJC (class 3B) with a 9.60 mm drill and limits of 9.346 to 9.639 mm. Letter U, at 9.347 mm, clears the UNJC minimum by 0.001 mm, so it fits inside both bands. Hartner's 9.60 mm UNJC drill does not work the other way: it is 0.0020 in over the UNC 2B maximum.
7/16-14 Helicoil and oversize repair
For a wire thread insert the hole is far bigger than the tap drill. AmesWeb's ASME B18.29.1 table gives an STI minor diameter of 0.453 to 0.4639 in and suggests 29/64 in, and the Albany County Fasteners sizing chart prints the same drill. Both sources agree, though with little to spare: 29/64 in is 0.4531 in, only 0.0001 in above the minimum. Hartner's insert table gives 11.60 mm (0.4567 in), nearer the middle of the same range, which helps if your 29/64 in drill cuts at or under its size.
Albany's chart also lists 7/16-14 as an oversize repair. When a 3/8-16 hole strips, its first step up is 7/16-14 with a U drill, and the step after that is 1/2-13. Its 7/16-14 row in turn names 1/2-13 as the first oversize.
7/16-14 roll and form taps
A forming tap pushes the thread up instead of cutting it, so the hole is bigger. Balax gives letter Y (0.404 in), Jarvis 13/32 in (0.4062 in) and Haas 10.3 mm (0.4055 in).
FAQ
What is the 7/16-14 tap drill size?
7/16-14 tap drill size is letter U (0.368 in, 9.35 mm), for about 75% thread inside class 2B.
What metric drill for 7/16-14?
9.4 mm, as Hartner prints, gives about 73% thread. Anything from 9.2 to 9.55 mm passes class 2B. Engineering Toolbox's 9.65 mm is 0.0039 in over the maximum.
Can I use 23/64 for 7/16-14?
Bolt Depot lists it next to U, but 23/64 in (0.3594 in) is 0.0006 in under the 2B minimum. Use U, or 3/8 in for an easier cut.
What drill for a 7/16-14 Helicoil?
29/64 in. AmesWeb and Albany County Fasteners both print it, and Hartner gives 11.60 mm. The STI hole runs from 0.453 to 0.4639 in, so 29/64 in (0.4531 in) is inside by only 0.0001 in.
Does a UNJC 7/16-14 take the same drill?
Letter U happens to fit both. Hartner's UNJC limits are 9.346 to 9.639 mm and U is 9.347 mm, but Hartner's own UNJC drill is 9.60 mm, which is too big for plain UNC 2B.
Related pages
Cite or reuse this data
Please quote these figures with a link to this page: TapDrillSize, "7/16-14 tap drill size", https://tapdrillsize.com/7-16-14-tap-drill-size/, published November 23, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.
Chart drills from American Fastener, Little Machine Shop, Starrett, Bolt Depot, Champion Cutting Tool, Emuge, Hartner (Gühring group) and Engineering Toolbox. Class 2B limits and the thread percentage formula from the OSG chart. UNJC and insert limits from Hartner (Gühring group). STI limits and drills from AmesWeb and Albany County Fasteners, oversize repairs from Albany. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on November 23, 2026.