#10-24 Tap Drill Size
#10-24 tap drill size is a #25 drill, 0.1495 in (3.80 mm). American Fastener, Little Machine Shop, Starrett and Bolt Depot print #25. It leaves about 75% thread inside the class 2B limits of 0.145 to 0.156 in from the OSG chart.
#10-24 is the coarse (UNC) thread on a #10 screw, 0.190 in across with 24 threads per inch. It shares that diameter with the fine #10-32, and the two are easy to mix up. Of the eight charts we read, two print a drill that is outside 2B for #10-24, and both of those drills suit #10-32 better.
What eight charts print, and the two that miss
| Chart | Kind | Drill printed | Diameter | Thread | 2B |
|---|---|---|---|---|---|
| American Fastener | Fastener supplier | #25 | 0.1495 in | 75% | Inside |
| Little Machine Shop | Tool supplier | #25 | 0.1495 in | 75% | Inside |
| Starrett | Tool maker | #25 | 0.1495 in | 75% | Inside |
| Bolt Depot | Fastener supplier | #25 or 5/32 in | 0.1495 / 0.1563 in | 75% / 62% | Inside / 0.0003 in over |
| Champion Cutting Tool | Tool maker | 3.7 mm or #25 | 0.1457 / 0.1495 in | 82% / 75% | Inside |
| Emuge | Tap maker | 0.1520 in (#24) | 0.1520 in | 70% | Inside |
| Hartner (Gühring group) | Drill maker | 3.9 mm | 0.1535 in | 67% | Inside |
| Engineering Toolbox | Reference site | 4.0 mm | 0.1575 in | 60% | 0.0015 in over |
Bolt Depot's second drill, 5/32 in, is 0.0003 in too big for 2B, and Engineering Toolbox's 4.0 mm is 0.0015 in too big. Both leave around 60% thread, a usable but out-of-class hole. Champion lists 3.7 mm first, a fuller thread than #25, and prints its own "probable percentage" of 76% for it and 69% for #25. The formula gives 82% and 75%, about 6 points higher.
Every drill near #25
Diameters from Wikipedia. Thread percentage is (0.190 − hole) / (1.299 / 24), the OSG formula. On #10-24, 2B allows about 63% to 83% thread.
| Drill | Diameter | Thread left | Class 2B |
|---|---|---|---|
| #27 | 0.1440 in (3.66 mm) | 85% | Under the min by 0.0010 in |
| 3.7 mm | 0.1457 in | 82% | Inside |
| #26 | 0.1470 in (3.73 mm) | 79% | Inside |
| 3.75 mm | 0.1476 in | 78% | Inside |
| #25 | 0.1495 in (3.80 mm) | 75% | Inside |
| 3.8 mm | 0.1496 in | 75% | Inside |
| 3.85 mm | 0.1516 in | 71% | Inside |
| #24 | 0.1520 in (3.86 mm) | 70% | Inside |
| 3.9 mm | 0.1535 in | 67% | Inside |
| #23 | 0.1540 in (3.91 mm) | 67% | Inside |
| 3.95 mm | 0.1555 in | 64% | Inside |
| 5/32 in | 0.1563 in (3.97 mm) | 62% | Over the max by 0.0003 in |
| #22 | 0.1570 in (3.99 mm) | 61% | Over the max by 0.0010 in |
| 4.0 mm | 0.1575 in | 60% | Over the max by 0.0015 in |
| #21 | 0.1590 in (4.04 mm) | 57% | Over the max by 0.0030 in |
Ten drills pass, from 3.7 mm to 3.95 mm. A 3.8 mm metric drill is only 0.0001 in bigger than #25, the closest substitute there is.
#10-24 or #10-32?
Both threads sit on the same 0.190 in screw. #10-32 has 32 threads per inch and takes a #21. That #21 is the last row above: 0.0030 in over the #10-24 maximum, leaving 57% thread. Going the other way, #25 in a #10-32 hole is 0.0065 in under its 0.156 in minimum, far too small for a #10-32 tap. Count the threads, or try a known nut, before you choose.
Both show up on 19-inch equipment racks: Wikipedia lists rack rails tapped for 10-32 UNF or 10-24 UNC screws, so a rack screw is not proof of either one.
Helicoil (STI) drill for #10-24
Drill 13/64 in (0.2031 in) for a #10-24 insert. That is the size AmesWeb lists from ASME B18.29.1, where the STI hole must measure 0.199 to 0.208 in. Be careful with the #10 on the Albany County Fasteners sizing chart, which it prints as 0.194 in: that falls about 0.005 in short of the range, so the sources disagree. Hartner's insert table agrees with AmesWeb instead, with 5.20 mm (0.2047 in) inside the same limits.
#10-24 roll and form taps
Balax and Jarvis print 11/64 in (0.1719 in) and Haas 4.3 mm (0.1693 in) for a #10-24 forming tap, 0.0026 in apart.
FAQ
What is the #10-24 tap drill size?
#10-24 tap drill size is a #25 drill, 0.1495 in (3.80 mm), for about 75% thread inside class 2B.
Is 5/32 OK for #10-24?
Not for class 2B. Bolt Depot lists 5/32 in, but at 0.15625 in it is 0.0003 in over the 2B maximum of 0.156 in. It is the right size for #10-32, not #10-24.
What metric drill for #10-24?
3.8 mm, almost exactly a #25. Hartner prints 3.9 mm, which also passes. Engineering Toolbox prints 4.0 mm, which is 0.0015 in over the 2B maximum.
Can I use the #10-32 drill for #10-24?
No. The #10-32 drill, #21, is 0.0030 in over the #10-24 2B maximum and leaves only about 57% thread.
What drill for a #10-24 Helicoil?
13/64 in, per AmesWeb's ASME B18.29.1 table, or 5.20 mm per Hartner. A chart printing #10 (0.194 in) for this insert is about 0.005 in under the STI minimum.
Related pages
Cite or reuse this data
Please quote these figures with a link to this page: TapDrillSize, "#10-24 tap drill size", https://tapdrillsize.com/10-24-tap-drill-size/, published November 12, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.
Chart drills from American Fastener, Little Machine Shop, Starrett, Bolt Depot, Champion Cutting Tool, Emuge, Hartner (Gühring group) and Engineering Toolbox. Class 2B limits and the thread percentage formula from the OSG chart. Rack rail threads from Wikipedia. STI limits and drills from AmesWeb and Albany County Fasteners. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on November 12, 2026.