9/16-12 Tap Drill Size

9/16-12 tap drill size is 31/64 in (0.4844 in, 12.30 mm). Five of the eight charts we compared print it as their only drill, Champion lists it second, and it leaves about 72% thread inside the class 2B hole limits of 0.472 to 0.490 in from the OSG chart.

9/16-12 is the coarse (UNC) 9/16 in thread, 12 threads per inch. It shows up as a repair size: the Albany County Fasteners oversize table lists it as the first step up for a stripped 1/2-13 hole and the second for a stripped 7/16-14, both with a 31/64 in drill.

What the charts print for 9/16-12

ChartKindDrillDiameterThread2B
American FastenerFastener supplier31/64 in0.4844 in72%Inside
Little Machine ShopTool supplier31/64 in0.4844 in72%Inside
StarrettTool maker31/64 in0.4844 in72%Inside
Bolt DepotFastener supplier31/64 in0.4844 in72%Inside
EmugeTap maker0.4844 in (31/64 in)0.4844 in72%Inside
Champion Cutting ToolTool maker15/32 in, then 31/64 in0.4688 / 0.4844 in87% / 72%15/32 0.0032 in under, 31/64 inside
Hartner (Gühring group)Drill maker12.2 mm0.4803 in76%Inside
Engineering ToolboxReference site12.6 mm0.4961 in61%0.0061 in over

Two charts miss, on opposite sides. Champion's first drill, 15/32 in, is too tight; Champion itself rates it at a "probable" 84% thread, and the OSG formula gives 87%. Engineering Toolbox's 12.6 mm is too loose and leaves about 61%. Hartner's 12.2 mm is the tighter of the passing answers.

9/16-12 drills from 15/32 in to 12.6 mm

Thread left is (0.5625 − hole) / (1.299 / 12). Class 2B on 9/16-12 spans about 67% to 84% thread. Diameters from Wikipedia.

DrillDiameterThread leftClass 2B
15/32 in0.4688 in (11.91 mm)87%Under the min by 0.0032 in
11.95 mm0.4705 in85%Under the min by 0.0015 in
12.0 mm0.4724 in83%Inside
12.1 mm0.4764 in80%Inside
12.2 mm0.4803 in76%Inside
12.3 mm0.4843 in72%Inside
31/64 in0.4844 in (12.30 mm)72%Inside
12.4 mm0.4882 in69%Inside
12.45 mm0.4902 in67%Over the max by 0.0002 in
12.6 mm0.4961 in61%Over the max by 0.0061 in

12.3 mm and 31/64 in differ by 0.0001 in. 12.45 mm looks like a reasonable step up and misses by 0.0002 in; 12.4 mm is the largest metric size in the band.

9/16-12 UNJC, and the M14 drill

For the rounded-root UNJC form, Hartner gives 12.40 mm, with class 3B limits of 12.228 to 12.482 mm. 31/64 in (12.303 mm) and 12.4 mm fall inside that band and inside UNC 2B. Hartner's own UNC drill, 12.2 mm, is 0.028 mm under the UNJC minimum.

9/16 in is 14.29 mm, close to M14. The M14 drill, 12.0 mm, passes 9/16-12 2B at about 83% thread, with 0.0004 in to spare. The other direction fails: 31/64 in is 0.093 mm over the M14 6H maximum of 12.210 mm. The pitches are 2.117 mm and 2 mm, so the screws don't swap.

A 9/16-12 insert drill outside its own range

AmesWeb's ASME B18.29.1 table gives an STI minor diameter of 0.5806 to 0.5918 in for 9/16-12, and in the same row suggests 19/32 in. But 19/32 in is 0.59375 in, about 0.002 in over that maximum. Albany County Fasteners prints the same 19/32 in. So two sources agree on a drill that is outside the range one of them publishes.

Hartner's insert table gives a drill inside the range. It gives the same range in millimetres, 14.747 to 15.032 mm, and a 14.90 mm drill (0.5866 in), near the middle. If you have only inch drills, no common fractional size lands inside: 37/64 in is 0.0025 in under the minimum and 19/32 in is over.

9/16-12 roll and form taps

Balax gives 0.521 in, Jarvis a 0.5257 in hole and Haas 13.3 mm (0.5236 in).

FAQ

What is the 9/16-12 tap drill size?

9/16-12 tap drill size is 31/64 in (0.4844 in, 12.30 mm), for about 72% thread inside class 2B.

What metric drill for 9/16-12?

12.3 mm is the same hole as 31/64 in. Hartner prints 12.2 mm (about 76%). Anything from 12.0 to 12.4 mm passes; Engineering Toolbox's 12.6 mm is 0.0061 in over.

Is 15/32 OK for 9/16-12?

No. Champion lists 15/32 in first, but at 0.4688 in it is 0.0032 in under the class 2B minimum.

What drill for a 9/16-12 Helicoil?

14.90 mm (0.5866 in), per Hartner. AmesWeb and Albany County Fasteners both print 19/32 in, which is about 0.002 in over AmesWeb's own STI maximum of 0.5918 in.

Can I use the M14 drill for 9/16-12?

Yes, just. 12.0 mm (0.4724 in) is inside 9/16-12 2B at about 83% thread. 31/64 in is too big for M14, though: 0.093 mm over its 6H maximum.

Related pages

Cite or reuse this data

Please quote these figures with a link to this page: TapDrillSize, "9/16-12 tap drill size", https://tapdrillsize.com/9-16-12-tap-drill-size/, published December 12, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.

Chart drills from American Fastener, Little Machine Shop, Starrett, Bolt Depot, Champion Cutting Tool, Emuge, Hartner (Gühring group) and Engineering Toolbox. Class 2B limits and the thread percentage formula from the OSG chart. M14 6H limits from Emuge and Hartner (Gühring group); UNJC and insert limits from Hartner (Gühring group). STI limits and drills from AmesWeb and Albany County Fasteners, oversize repairs from Albany. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on December 12, 2026.