3/8-24 Tap Drill Size

3/8-24 tap drill size is letter Q (0.332 in, 8.43 mm). It leaves about 79% thread inside the class 2B hole limits of 0.330 to 0.340 in from the OSG chart. Four of the eight charts we read give 8.5 mm (Emuge as the decimal 0.3346 in), which leaves about 75% and also passes.

3/8-24 is the fine (UNF) 3/8 in thread with 24 threads per inch. One place it turns up is car brake plumbing: a common inverted flare tube nut for 3/16 in brake line has a 3/8-24 UNF thread, as Sherco Auto's specification lists, so a hand-made block or adapter for that line is tapped 3/8-24.

3/8-24: letter Q or 8.5 mm

The eight charts split between letter Q and 8.5 mm, and both answers are good.

ChartKindDrillDiameterThread2B
American FastenerFastener supplierQ0.3320 in79%Inside
Little Machine ShopTool supplierQ0.3320 in79%Inside
StarrettTool makerQ0.3320 in79%Inside
Bolt DepotFastener supplierQ or 21/64 in0.3320 / 0.3281 in79% / 87%Q inside, 21/64 0.0019 in under
Champion Cutting ToolTool makerQ or 8.5 mm0.3320 / 0.3346 in79% / 75%Inside
EmugeTap maker0.3346 in (8.5 mm)0.3346 in75%Inside
Hartner (Gühring group)Drill maker8.5 mm0.3346 in75%Inside
Engineering ToolboxReference site8.5 mm0.3346 in75%Inside

The one miss is Bolt Depot's second drill. 21/64 in is the nearest fractional size below Q, and on this thread that is 0.0019 in too small. Champion's own "probable percentage" figures, 75% for Q and 70% for 8.5 mm, run 4 to 5 points below the OSG formula.

3/8-24 drills from 8.3 mm up

Thread left is (0.375 − hole) / (1.299 / 24). The 2B band on 3/8-24 is only 0.010 in wide, about 65% to 83% thread. Diameters from Wikipedia.

DrillDiameterThread leftClass 2B
8.3 mm0.3268 in89%Under the min by 0.0032 in
21/64 in0.3281 in (8.33 mm)87%Under the min by 0.0019 in
8.4 mm0.3307 in82%Inside
Letter Q0.3320 in (8.43 mm)79%Inside
8.5 mm0.3346 in75%Inside
8.6 mm0.3386 in67%Inside
Letter R0.3390 in (8.61 mm)67%Inside
8.7 mm0.3425 in60%Over the max by 0.0025 in
11/32 in0.3438 in (8.73 mm)58%Over the max by 0.0037 in

Letter R is the biggest drill that passes, with 0.001 in to spare, and it is the easiest on the tap. 11/32 in, the next fractional size, is too big.

3/8-24 UNJF

UNJF has the same 24 pitch but a rounded root and a larger internal minor diameter. Hartner gives 8.60 mm for it, with limits of 8.494 to 8.679 mm. Letter Q is 0.061 mm under that minimum, so a Q hole is too small for UNJF. 8.5 mm is the smallest common drill that fits both: it is inside the UNJF band by 0.006 mm and inside UNF 2B too.

3/8-24 Helicoil drill

AmesWeb's ASME B18.29.1 table puts the STI hole at 0.384 to 0.391 in and suggests letter W (0.386 in). Albany County Fasteners prints 25/64 in (0.3906 in), and Hartner's insert table gives 9.80 mm (0.3858 in) with limits of 9.754 to 9.931 mm. All three are inside. Albany's is the largest hole, 0.0004 in under the maximum, while W and 9.80 mm sit near the bottom of the range.

3/8-24 roll and form taps

Balax and Haas both give 9.0 mm (0.3543 in) for a forming tap. Jarvis gives the hole as 0.3566 in and names no drill for it.

FAQ

What is the 3/8-24 tap drill size?

3/8-24 tap drill size is letter Q (0.332 in, 8.43 mm), for about 79% thread inside class 2B. 8.5 mm also passes, at about 75%.

Is 21/64 OK for 3/8-24?

No. Bolt Depot lists it next to Q, but 21/64 in (0.3281 in) is 0.0019 in under the class 2B minimum.

What tap drill for a 3/16 brake line port?

A common inverted flare nut for 3/16 in brake line, such as Sherco Auto's, is 3/8-24 UNF, so a port for it takes a 3/8-24 tap and a Q or 8.5 mm drill.

What drill for a 3/8-24 Helicoil?

Letter W (0.386 in), per AmesWeb. Albany County Fasteners gives 25/64 in and Hartner 9.80 mm. All three fit the STI hole of 0.384 to 0.391 in.

What drill for 3/8-24 UNJF?

Hartner gives 8.60 mm, with limits of 8.494 to 8.679 mm. A plain 8.5 mm drill fits both UNJF and UNF 2B; Q is too small for UNJF.

Related pages

Cite or reuse this data

Please quote these figures with a link to this page: TapDrillSize, "3/8-24 tap drill size", https://tapdrillsize.com/3-8-24-tap-drill-size/, published November 26, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.

Chart drills from American Fastener, Little Machine Shop, Starrett, Bolt Depot, Champion Cutting Tool, Emuge, Hartner (Gühring group) and Engineering Toolbox. Class 2B limits and the thread percentage formula from the OSG chart. UNJF and insert limits from Hartner (Gühring group). STI limits and drills from AmesWeb and Albany County Fasteners. Brake line nut thread from Sherco Auto. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on November 26, 2026.