5/16-24 Tap Drill Size

5/16-24 tap drill size is letter I (0.272 in, 6.91 mm). It leaves about 75% thread inside the class 2B hole limits of 0.267 to 0.277 in from the OSG chart. Three of the charts give 6.9 mm instead (Emuge as the decimal 0.2717 in), which is the same hole for every practical purpose.

5/16-24 is the fine (UNF) 5/16 in thread, 24 threads per inch. Every one of the eight charts we read gives a drill inside 2B here. The real disagreement on 5/16-24 is in a different table: the drill for a wire thread insert.

5/16-24: letter I or 6.9 mm

ChartKindDrillDiameterThread2B
American FastenerFastener supplierI0.2720 in75%Inside
Little Machine ShopTool supplierI0.2720 in75%Inside
StarrettTool makerI0.2720 in75%Inside
Bolt DepotFastener supplierI0.2720 in75%Inside
Champion Cutting ToolTool maker6.8 mm, then I0.2677 / 0.2720 in83% / 75%Inside
EmugeTap maker0.2717 in (6.9 mm)0.2717 in75%Inside
Hartner (Gühring group)Drill maker6.9 mm0.2717 in75%Inside
Engineering ToolboxReference site6.9 mm0.2717 in75%Inside

Letter I and 6.9 mm differ by 0.0003 in. Champion is the one chart that leads with a tighter hole: 6.8 mm, which it rates at a "probable" 78% thread (the OSG formula gives 83%). It is still inside 2B, with 0.0007 in to spare.

5/16-24 drills from 6.75 to 7.05 mm

Thread left is (0.3125 − hole) / (1.299 / 24). The 2B band is 0.010 in wide, about 66% to 84% thread. Diameters from Wikipedia.

DrillDiameterThread leftClass 2B
6.75 mm0.2657 in86%Under the min by 0.0013 in
Letter H0.2660 in (6.76 mm)86%Under the min by 0.0010 in
6.8 mm0.2677 in83%Inside
6.85 mm0.2697 in79%Inside
6.9 mm0.2717 in75%Inside
Letter I0.2720 in (6.91 mm)75%Inside
6.95 mm0.2736 in72%Inside
7.0 mm0.2756 in68%Inside
Letter J0.2770 in (7.04 mm)66%Inside
7.05 mm0.2776 in65%Over the max by 0.0006 in

Letter H, one size below I, is 0.0010 in too small. Letter J, one above, still passes at about 66%, right at the maximum, which makes it the easiest on the tap of the drills that pass. 7.05 mm is just over.

One drill for 5/16-24 and M8 x 1

5/16 in is 7.94 mm, close to 8 mm, and 24 threads per inch is a 1.058 mm pitch, close to the 1 mm of M8 x 1, the fine M8. They are not interchangeable, but their holes overlap. Hartner gives 7.00 mm for M8 x 1, with 6H limits of 6.917 to 7.153 mm, and 7.0 mm is also inside 5/16-24 2B at about 68% thread. Letter I is 0.008 mm under the M8 x 1 minimum. So 7.0 mm is the safest drill for both; 6.95 mm and letter J also fit both bands. For the coarse thread, see M8.

The 5/16-24 insert drill: three sources, one wrong

AmesWeb's ASME B18.29.1 table puts the STI hole for 5/16-24 at 0.3215 to 0.3288 in and suggests letter P (0.323 in). Hartner's insert table gives 8.25 mm (0.3248 in), with limits of 8.166 to 8.352 mm, the same range. Those two agree.

The Albany County Fasteners sizing chart does not. Its 5/16-24 row lists letter I, 0.272 in, against the 5/16-24 STI tap. That is the ordinary tap drill from the table above, and it is 0.0495 in under the STI minimum. Use P or 8.25 mm.

5/16-24 UNJF and form taps

UNJF has the same pitch with a rounded root and a larger internal minor diameter. Hartner gives 7.00 mm for 5/16-24 UNJF, with class 3B limits of 6.906 to 7.109 mm. Letter I (6.909 mm) is inside that band by 0.003 mm; 6.9 mm is 0.006 mm under it.

For a forming tap, Balax gives 0.293 in, Jarvis letter M (0.295 in) and Haas 7.4 mm (0.2913 in).

FAQ

What is the 5/16-24 tap drill size?

5/16-24 tap drill size is letter I (0.272 in, 6.91 mm), for about 75% thread inside class 2B.

What metric drill for 5/16-24?

6.9 mm, the drill on the metric-minded charts, is 0.0003 in smaller than letter I and leaves the same 75%. Anything from 6.8 to 7.0 mm passes 2B.

Is one drill good for both 5/16-24 and M8 x 1?

Yes, 7.0 mm. It leaves about 68% thread on 5/16-24, inside 2B, and it is the drill Hartner gives for M8 x 1, inside that thread's 6H limits of 6.917 to 7.153 mm.

What drill for a 5/16-24 Helicoil?

Letter P (0.323 in), per AmesWeb, or 8.25 mm per Hartner. Albany County Fasteners prints letter I, the plain tap drill, which is about 0.05 in too small for an insert.

What drill for 5/16-24 UNJF?

Hartner gives 7.00 mm, with limits of 6.906 to 7.109 mm. Letter I just fits that band too; 6.9 mm is 0.006 mm under it.

Related pages

Cite or reuse this data

Please quote these figures with a link to this page: TapDrillSize, "5/16-24 tap drill size", https://tapdrillsize.com/5-16-24-tap-drill-size/, published December 3, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.

Chart drills from American Fastener, Little Machine Shop, Starrett, Bolt Depot, Champion Cutting Tool, Emuge, Hartner (Gühring group) and Engineering Toolbox. Class 2B limits and the thread percentage formula from the OSG chart. UNJF, M8 x 1 and insert limits from Hartner (Gühring group). STI limits and drills from AmesWeb and Albany County Fasteners. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on December 3, 2026.