1/4-20 Tap Drill Size
1/4-20 tap drill size is a #7 drill, 0.201 in (5.1 mm). American Fastener, Little Machine Shop, Starrett and Bolt Depot all print #7. It leaves about 75% of a full thread and sits inside the class 2B hole limits of 0.196 to 0.207 in from the OSG chart.
1/4-20 is the coarse (UNC) quarter-inch thread: 0.250 in across with 20 threads per inch. #7 is the textbook answer, but the published charts do not all agree. We read eight of them, and between them they print six different drills for this one thread.
What eight tap drill charts say for 1/4-20
Each row is one published chart and the drill it prints for 1/4-20. The thread percentage and the class 2B check are ours, worked out from each drill's diameter.
| Chart | Who publishes it | Drill printed | Diameter | Thread left | Class 2B |
|---|---|---|---|---|---|
| American Fastener | Fastener supplier | #7 | 0.2010 in | 75% | Inside |
| Little Machine Shop | Tool supplier | #7 | 0.2010 in | 75% | Inside |
| Starrett | Tool maker | #7 | 0.2010 in | 75% | Inside |
| Bolt Depot | Fastener supplier | #7 or 13/64 in | 0.2010 / 0.2031 in | 75% / 72% | Inside |
| Champion Cutting Tool | Tool maker | #9, #7 or 13/64 in | 0.1960 / 0.2010 / 0.2031 in | 83% / 75% / 72% | Inside |
| Emuge | Tap maker | 0.2040 in (#6) | 0.2040 in | 71% | Inside |
| Hartner (Gühring group) | Drill maker | 5.1 mm | 0.2008 in | 76% | Inside |
| Engineering Toolbox | Reference site | 5.35 mm | 0.2106 in | 61% | Over the max by 0.0036 in |
Fabworks and Microform Precision print the same 75% drill as Little Machine Shop. Seven of the eight charts land inside class 2B. The odd one out is Engineering Toolbox: its 5.35 mm hole is about 0.09 mm too big for 2B.
The spread is wider than it looks. Champion's first choice, #9, sits exactly on the 2B minimum, and Engineering Toolbox's 5.35 mm sits over the maximum, so the eight charts span the whole tolerance and a little more. Champion also prints its own "probable percentage of thread" for each drill: 77%, 70% and 66%. Those run about 6 points under the formula's 83%, 75% and 72%, and Champion does not say how it works them out.
Fabworks adds a second drill for tougher metal: 7/32 in (0.2188 in), labelled "50% thread for steel, stainless and iron". By the formula it leaves about 48%, and the hole is 0.0118 in over the 2B maximum. It makes tapping steel easier, but it is not a class 2B hole. If the drawing calls for 2B, stay at #5 or smaller.
The class 2B window for 1/4-20
Class 2B, the usual tolerance for an inch internal thread, allows a 1/4-20 hole from 0.196 to 0.207 in (OSG). In thread percentage that is about 66% to 83%. The OSG chart also prints the hole for each percentage:
| Thread | OSG hole | That hole against 2B | Nearest drill |
|---|---|---|---|
| 80% | 0.1980 in | Inside | #8 (0.199 in) |
| 75% | 0.2013 in | Inside | #7 (0.201 in) |
| 70% | 0.2045 in | Inside | #6 (0.204 in) |
| 65% | 0.2078 in | 0.0008 in over the max | #4 (0.209 in) |
| 60% | 0.2110 in | 0.0040 in over the max | #4 or #3 (0.209 or 0.213 in) |
So on 1/4-20, class 2B needs at least about 66% thread. A 65% thread, the top of the 55 to 65% range OSG calls enough for most work, is already slightly over the maximum.
Every drill near 1/4-20, and where it lands
Number, fractional and metric drills between 0.196 and 0.211 in, with diameters from Wikipedia:
| Drill | Diameter | Thread left | Class 2B |
|---|---|---|---|
| #9 | 0.1960 in (4.98 mm) | 83% | Inside |
| 5.0 mm | 0.1969 in | 82% | Inside |
| #8 | 0.1990 in (5.05 mm) | 79% | Inside |
| 5.1 mm | 0.2008 in | 76% | Inside |
| #7 | 0.2010 in (5.11 mm) | 75% | Inside |
| 13/64 in | 0.2031 in (5.16 mm) | 72% | Inside |
| #6 | 0.2040 in (5.18 mm) | 71% | Inside |
| 5.2 mm | 0.2047 in | 70% | Inside |
| #5 | 0.2055 in (5.22 mm) | 69% | Inside |
| 5.3 mm | 0.2087 in | 64% | Over the max by 0.0017 in |
| #4 | 0.2090 in (5.31 mm) | 63% | Over the max by 0.0020 in |
| 5.35 mm | 0.2106 in | 61% | Over the max by 0.0036 in |
Nine drills pass, and every one from #9 to #5 will do. For aluminum and brass, the standard #7 or 5.1 mm, at about 75%, is the usual choice. In steel or stainless, #6, 5.2 mm or #5 is easier on the tap and still inside 2B. Stop at #5: the next number drill, #4, is out.
The camera tripod thread is 1/4-20
The screw on a camera tripod or quick-release plate is a 1/4-20 UNC thread, set by ISO 1222 and DIN 4503-1. The larger thread in the same standards is 3/8-16 (threadingtoolsguide.com). If you are tapping a camera plate, a rig part or a mount, it is the same thread and the same drill as on this page. A mount that needs the bigger 3/8-16 thread takes a 5/16 in drill instead.
The same source gives a 5.35 mm core hole for the tripod thread. That is the Engineering Toolbox figure again: about 61% thread, a little over the class 2B maximum. A tripod screw will turn into it, but for a 2B thread use #7 or 5.1 mm.
Repairing a stripped 1/4-20 thread
A thread insert restores the original 1/4-20 size in a bigger hole. It needs its own drill and an STI tap. A plain 1/4-20 tap will not work (Albany County Fasteners), because the STI hole is bigger to make room for the coil's wire (AmesWeb).
- AmesWeb, following ASME B18.29.1, gives a 17/64 in drill for a 1/4-20 STI hole, with hole limits of 0.2608 to 0.2704 in. 17/64 in is 0.2656 in, the middle of that range.
- Albany County Fasteners prints #3 (0.213 in) for the same insert. That is 0.048 in under the STI minimum, so an STI tap would jam or break. #3 is the standard drill for a plain 1/4-28 tap, far too small for an insert. Use 17/64 in.
The other fix is to go up a size. The Albany chart lists 5/16-18 with an F drill as the first oversize for a 1/4-20 hole, if the part allows a bigger screw.
1/4-20 roll and form taps
A forming tap needs a bigger hole than #7. Three makers agree within 0.002 in: Balax gives 5.75 mm (0.2264 in), Jarvis a #1 drill (0.228 in) and Haas 5.8 mm (0.2283 in).
Clearance hole for a 1/4 screw
For a hole the screw passes through rather than threads into, Fabworks gives an F drill, 0.257 in, for a close fit and an H drill, 0.266 in, for a free fit. Published clearance charts do not all agree on these, so if a drawing names a fit class, use the drill it gives.
1/4-20, 1/4-28 and M6
| Thread | Diameter | Pitch | Standard drill |
|---|---|---|---|
| 1/4-20 UNC | 6.35 mm | 1.270 mm (20 TPI) | #7 |
| 1/4-28 UNF | 6.35 mm | 0.907 mm (28 TPI) | #3 |
| M6 x 1.0 | 6.00 mm | 1.000 mm | 5.0 mm |
1/4-28 has the same diameter and a finer pitch, so it takes a bigger drill. M6 is 0.35 mm smaller with a different pitch. Neither screw fits the other's hole.
The finer pitch also leaves more steel in the screw's core. With the Unified thread stress area formula, (π/4) x (diameter − 0.9743 / TPI)² (Engineering Toolbox), a 1/4-20 screw has 0.0318 in² of tensile stress area and a 1/4-28 screw 0.0364 in², about 14% more.
FAQ
What is the 1/4-20 tap drill size?
1/4-20 tap drill size is a #7 drill, 0.201 in (5.1 mm), for about 75% thread inside class 2B.
Is 13/64 OK for 1/4-20?
Yes. 13/64 in leaves about 72% thread, inside class 2B. Bolt Depot and Champion list it next to #7.
What metric drill can I use for 1/4-20?
5.1 mm, the closest match to #7, as Hartner prints. 5.2 mm also passes 2B; 5.3 mm does not.
Why does Engineering Toolbox say 5.35 mm for 1/4-20?
It is the only one of the eight charts to print it. The hole leaves about 61% thread, 0.0036 in over the 2B maximum: a working thread, but shallower than 2B allows.
What drill do I use for a 1/4-20 Helicoil?
17/64 in, with a 1/4-20 STI tap (ASME B18.29.1, via AmesWeb). A chart printing #3 for this insert is wrong by 0.048 in.
What clearance hole do I drill for a 1/4 screw?
Fabworks gives an F drill (0.257 in) for a close fit and an H drill (0.266 in) for a free fit.
What drill for a 1/4-20 roll tap?
About 0.227 in: 5.75 mm (Balax), #1 (Jarvis) or 5.8 mm (Haas). Never #7.
Related pages
Cite or reuse this data
Please quote these figures with a link to this page: TapDrillSize, "1/4-20 tap drill size", https://tapdrillsize.com/1-4-20-tap-drill-size/, published November 4, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.
Chart drills from American Fastener, Little Machine Shop, Starrett, Bolt Depot, Engineering Toolbox, Champion Cutting Tool, Emuge and Hartner (Gühring group). Class 2B limits and percentage holes from the OSG chart, which also gives the thread percentage formula. STI hole limits and drill from AmesWeb (ASME B18.29.1). Insert chart from Albany County Fasteners. Steel and clearance drills from Fabworks. Tripod thread from threadingtoolsguide.com. Form tap drills from Balax, Jarvis and Haas. Stress area formula from Engineering Toolbox. Drill diameters from Wikipedia. Published on November 4, 2026.