#2-56 Tap Drill Size

#2-56 tap drill size is a #50 drill (0.070 in, 1.78 mm). Six of the eight charts we compared print #50 (Champion as its second choice), and it leaves about 69% thread inside the class 2B hole limits of 0.0667 to 0.0737 in from the OSG chart.

#2-56 is a number 2 machine screw, 0.086 in across, with 56 threads per inch (UNC). On a screw this small the 2B band is wide in percentage terms: it runs from about 53% to 83% thread. That wide band is why all eight charts pass here even though they print four different drills.

Four different drills, all inside 2B

ChartKindDrillDiameterThread2B
American FastenerFastener supplier#500.0700 in69%Inside
Little Machine ShopTool supplier#500.0700 in69%Inside
StarrettTool maker#500.0700 in69%Inside
Bolt DepotFastener supplier#500.0700 in69%Inside
EmugeTap maker0.0700 in (#50)0.0700 in69%Inside
Champion Cutting ToolTool maker#51, then #500.0670 / 0.0700 in82% / 69%Inside
Engineering ToolboxReference site1.8 mm0.0709 in65%Inside
Hartner (Gühring group)Drill maker1.85 mm0.0728 in57%Inside

From Champion's #51 to Hartner's 1.85 mm is a 0.0058 in spread, and both are 2B holes. They are not the same hole, though. #51 leaves about 82% thread, close to the 2B minimum diameter, and Hartner's 1.85 mm leaves about 57%, close to the maximum. Champion's own "probable percentage" is lower than the OSG formula gives: 74% for #51 and 62% for #50.

Hartner prints its 2B limits next to the drill, 1.694 to 1.872 mm, which in inches are the same 0.0667 to 0.0737 in that OSG gives.

#2-56 drills from #52 to #48

Number drills step about 0.003 in at this size, and each step moves the thread by roughly 13 points. Thread left is (0.086 − hole) / (1.299 / 56). Diameters from Wikipedia.

DrillDiameterThread leftClass 2B
#520.0635 in (1.61 mm)97%Under the min by 0.0032 in
1.65 mm0.0650 in91%Under the min by 0.0017 in
1.7 mm0.0669 in82%Inside
#510.0670 in (1.70 mm)82%Inside
1.75 mm0.0689 in74%Inside
#500.0700 in (1.78 mm)69%Inside
1.8 mm0.0709 in65%Inside
1.85 mm0.0728 in57%Inside
#490.0730 in (1.85 mm)56%Inside
1.9 mm0.0748 in48%Over the max by 0.0011 in
#480.0760 in (1.93 mm)43%Over the max by 0.0023 in

Three number drills pass, #51, #50 and #49, plus four metric sizes from 1.7 to 1.85 mm. #52 would leave about 97%, close to a full-depth thread, and is under the 2B minimum. At the other end, #49 is the loosest number drill that still passes.

#2-56 vs M2.5

M2.5 is the nearest common metric screw, but it is bigger: 2.5 mm across against 2.18 mm for #2-56, with a 0.45 mm pitch against 0.454 mm. The M2.5 drill, 2.05 mm (0.0807 in), is 0.0070 in over the #2-56 2B maximum, and #50 is 0.235 mm under the M2.5 6H minimum of 2.013 mm. The fine #2-64 takes the same 1.85 mm drill in Hartner's chart, with its own limits of 1.755 to 1.910 mm.

#2-56 Helicoil drill

AmesWeb lists #2-56 in its ASME B18.29.1 table with an STI hole of 0.0899 to 0.0961 in and a #42 drill (0.0935 in), close to the middle. The other two insert sources we use don't go this small: Albany County Fasteners starts at #4-40 and Hartner's insert table at #6. So AmesWeb's figure is the only one we can give, and we have not been able to check it against a second source.

#2-56 roll and form taps

Jarvis and Haas both give 5/64 in (0.0781 in). Balax gives #47 (0.0785 in) or 2.0 mm (0.0787 in), nearly the same hole.

FAQ

What is the #2-56 tap drill size?

#2-56 tap drill size is a #50 drill (0.070 in, 1.78 mm), for about 69% thread inside class 2B.

What metric drill for #2-56?

1.8 mm (about 65% thread) is the closest to #50. Anything from 1.7 to 1.85 mm passes class 2B; 1.9 mm is 0.0011 in over.

Is #51 or #49 OK for #2-56?

Both pass class 2B. #51 leaves about 82% thread, near the top of the band, and #49 about 56%, near the bottom.

Can I use the M2.5 drill for #2-56?

No. 2.05 mm (0.0807 in) is 0.0070 in over the #2-56 2B maximum. #2-56 is smaller than M2.5, at 0.086 in (2.18 mm) across.

What drill for a #2-56 Helicoil?

A #42 (0.0935 in), per AmesWeb's ASME B18.29.1 table, inside an STI hole of 0.0899 to 0.0961 in.

Related pages

Cite or reuse this data

Please quote these figures with a link to this page: TapDrillSize, "#2-56 tap drill size", https://tapdrillsize.com/2-56-tap-drill-size/, published November 27, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.

Chart drills from American Fastener, Little Machine Shop, Starrett, Bolt Depot, Champion Cutting Tool, Emuge, Hartner (Gühring group) and Engineering Toolbox. Class 2B limits and the thread percentage formula from the OSG chart, #2-64 limits from Hartner (Gühring group). M2.5 6H limits from Emuge and Hartner (Gühring group). STI limits and drill from AmesWeb. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on November 27, 2026.