M6 Tap Drill Size
M6 tap drill size is 5.0 mm (0.197 in) for the standard M6 x 1.0 coarse thread. Starrett, Champion Cutting Tool, Emuge and Hartner (Gühring group) all print 5.0 mm. It leaves about 77% of a full thread and sits inside the class 6H limits of 4.917 to 5.153 mm.
The 5.0 mm figure is the major diameter minus the pitch, and four of the five charts we read agree on it. The fifth does not, and its figure is outside the tolerance.
Four charts say 5.0 mm, one says 5.2 mm
| Source | Type | Drill for M6 | Thread | Against 6H |
|---|---|---|---|---|
| Starrett | Tool maker | 5.0 mm | 77% | Inside |
| Champion Cutting Tool | Tool maker | 5.0 mm | 77% | Inside |
| Emuge | Tap maker | 5.0 mm | 77% | Inside |
| Hartner (Gühring group) | Drill maker | 5.0 mm | 77% | Inside |
| Bolt Depot | Fastener supplier | 5.2 mm | 62% | Over the max by 0.047 mm |
Bolt Depot's 5.2 mm leaves about 62% thread by the OSG formula, and the hole is 0.047 mm too big for class 6H. It still makes a usable thread, but not one that passes a 6H gauge. The figure does have a home: Hartner prints 5.2 mm, with 6H limits of 5.188 to 5.378 mm, for the fine M6 x 0.75 thread. On coarse M6 it is 0.047 mm too big.
One drill for M6 and 1/4-20
M6 and 1/4-20 are 0.35 mm apart in diameter, close enough to mix up. They are not interchangeable, but they can share a drill. A #7 drill, 0.201 in (5.105 mm), is the standard 1/4-20 drill, and it also fits inside the M6 6H band:
| M6 x 1.0 | 1/4-20 UNC | |
|---|---|---|
| Hole limits | 4.917 to 5.153 mm (6H) | 4.978 to 5.258 mm (2B) |
| Thread left by #7 | about 69% | about 75% |
| #7 against the limits | Inside | Inside |
So a shop that taps both threads can keep one #7 drill for them. The 1/4-20 limits are 0.196 to 0.207 in from the OSG chart, shown here in mm. The two taps are still different: 1/4-20 has 20 threads per inch (1.27 mm pitch) against 1.0 mm on M6.
M6 with number and fractional drills
Number drills step in small increments through this range, so several fit. Diameters from Wikipedia:
| Drill | Diameter | Thread left | Class 6H |
|---|---|---|---|
| #12 | 4.801 mm (0.189 in) | 92% | Under the min by 0.116 mm |
| #11 | 4.851 mm (0.191 in) | 88% | Under the min by 0.066 mm |
| 4.9 mm | 4.900 mm | 85% | Under the min by 0.017 mm |
| #10 | 4.915 mm (0.1935 in) | 84% | Under the min by 0.002 mm |
| #9 | 4.978 mm (0.196 in) | 79% | Inside |
| 5.0 mm | 5.000 mm | 77% | Inside |
| #8 | 5.055 mm (0.199 in) | 73% | Inside |
| 5.1 mm | 5.100 mm | 69% | Inside |
| #7 | 5.105 mm (0.201 in) | 69% | Inside |
| 13/64 in | 5.159 mm (0.2031 in) | 65% | Over the max by 0.006 mm |
| #6 | 5.182 mm (0.204 in) | 63% | Over the max by 0.029 mm |
| 5.2 mm | 5.200 mm | 62% | Over the max by 0.047 mm |
#9 is the closest inch drill to 5.0 mm. #10 looks like it should work but is 0.002 mm under the minimum, and 13/64 in is 0.006 mm over the maximum. Both would make a working thread, but neither passes 6H on paper.
The thread in server rack cage nuts
Cage nuts clip into the square holes of a 19-inch equipment rack. Outside the US they are M5 for light and medium equipment and M6 for heavier equipment such as servers, while 10-32 is more usual in the US (Wikipedia). Sysracks names the EIA-310-D rack standard for its M6 set, and Access Communications lists its cage nuts as M6 for standard 19-inch racks. Cage nuts in other threads are sold too, so check the screw you have. A part that bolts into the rack only needs a clearance hole. The 5.0 mm drill is for when you tap the M6 thread yourself, for example in a rail or bracket that takes rack screws directly.
M6 roll and form taps
A roll tap pushes the thread into shape instead of cutting it, so it starts from a larger hole. Balax and Haas print 5.5 mm, and Jarvis prints a 7/32 in drill (5.556 mm). The two figures are 0.056 mm apart.
FAQ
What is the M6 tap drill size?
M6 tap drill size is 5.0 mm (0.197 in) for the standard M6 x 1.0 thread, about 77% thread and inside class 6H.
Is 5.2 mm right for M6?
Not for the standard M6 x 1.0. Bolt Depot prints 5.2 mm, but that hole is 0.047 mm over the 6H maximum. 5.2 mm is the right drill for the fine M6 x 0.75.
What number drill can I use for M6?
A #9 (4.978 mm) is closest to 5.0 mm. #8 and #7 also pass 6H. #10 misses the minimum by 0.002 mm.
Can one drill do both M6 and 1/4-20?
Yes, a #7 (0.201 in, 5.105 mm). It is the standard 1/4-20 drill and also leaves about 69% thread in M6, inside class 6H.
What thread are rack cage nuts?
It depends where the equipment comes from. Wikipedia gives 10-32 as usual in the US, and M5 for light and M6 for heavier equipment such as servers elsewhere. Check the old screw.
Related pages
Cite or reuse this data
Please quote these figures with a link to this page: TapDrillSize, "M6 tap drill size", https://tapdrillsize.com/m6-tap-drill-size/, published November 4, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.
Chart drills from Starrett, Champion Cutting Tool, Emuge, Hartner (Gühring group) and Bolt Depot. Class 6H limits from Emuge and Hartner (Gühring group), and the M6 x 0.75 row from Hartner (Gühring group). 1/4-20 class 2B limits and the thread percentage formula from the OSG chart. Cage nut listings from Sysracks and Access Communications. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on November 4, 2026.