3/4-10 Tap Drill Size
3/4-10 tap drill size is 21/32 in (0.6562 in, 16.67 mm). It leaves about 72% thread, inside the class 2B hole limits of 0.642 to 0.663 in from the OSG chart, and five of the eight charts we read print it as their only answer.
3/4-10 is the coarse (UNC) 3/4 in thread with 10 threads per inch, a pitch of 2.54 mm. At this size a 2B hole is 0.021 in wide, so there is room for several drills. Even so, two of the eight charts give a drill that falls outside it, and they miss on opposite sides.
Where the charts split on 3/4-10
| Chart | Kind | Drill | Diameter | Thread | 2B |
|---|---|---|---|---|---|
| American Fastener | Fastener supplier | 21/32 in | 0.6562 in | 72% | Inside |
| Little Machine Shop | Tool supplier | 21/32 in | 0.6562 in | 72% | Inside |
| Starrett | Tool maker | 21/32 in | 0.6562 in | 72% | Inside |
| Bolt Depot | Fastener supplier | 21/32 in | 0.6562 in | 72% | Inside |
| Emuge | Tap maker | 0.6562 in (21/32 in) | 0.6562 in | 72% | Inside |
| Champion Cutting Tool | Tool maker | 41/64 in, then 21/32 in | 0.6406 / 0.6562 in | 84% / 72% | 41/64 0.0014 in under, 21/32 inside |
| Hartner (Gühring group) | Drill maker | 16.5 mm | 0.6496 in | 77% | Inside |
| Engineering Toolbox | Reference site | 17.0 mm | 0.6693 in | 62% | 0.0063 in over |
Champion is the odd one. Its first drill for 3/4-10 is 41/64 in, which it rates at a "probable" 81% thread, and the OSG formula puts it at 84%. Either way it is too tight for class 2B, by 0.0014 in. Its second drill, 21/32 in, matches everyone else. Engineering Toolbox misses the other way: its 17.0 mm leaves about 62% thread and is 0.0063 in over the maximum.
3/4-10 drills from 16.25 to 17.0 mm
Thread left is (0.750 − hole) / (1.299 / 10); 2B on 3/4-10 spans about 67% to 83% thread. Diameters from Wikipedia.
| Drill | Diameter | Thread left | Class 2B |
|---|---|---|---|
| 16.25 mm | 0.6398 in | 85% | Under the min by 0.0022 in |
| 41/64 in | 0.6406 in (16.27 mm) | 84% | Under the min by 0.0014 in |
| 16.3 mm | 0.6417 in | 83% | Under the min by 0.0003 in |
| 16.4 mm | 0.6457 in | 80% | Inside |
| 16.5 mm | 0.6496 in | 77% | Inside |
| 16.6 mm | 0.6535 in | 74% | Inside |
| 21/32 in | 0.6562 in (16.67 mm) | 72% | Inside |
| 16.7 mm | 0.6575 in | 71% | Inside |
| 16.8 mm | 0.6614 in | 68% | Inside |
| 16.9 mm | 0.6654 in | 65% | Over the max by 0.0024 in |
| 17.0 mm | 0.6693 in | 62% | Over the max by 0.0063 in |
Five metric sizes pass, from 16.4 to 16.8 mm. 16.3 mm is the near miss, 0.0003 in small. For a 3/4 in hand tap, which takes real effort at 72% thread, the 16.7 or 16.8 mm end of the range lightens the cut and still passes.
3/4-10 vs M20
3/4 in is 19.05 mm, a little under M20, and the pitches are close too: 2.54 mm against 2.5 mm. They still are not interchangeable, and neither is their drill. The M20 drill, 17.5 mm (0.6890 in), is 0.0260 in over the 3/4-10 2B maximum; 21/32 in is 0.625 mm under the M20 6H minimum of 17.294 mm.
3/4-10 Helicoil and oversize repair
On this size the two insert charts we compared agree. AmesWeb's ASME B18.29.1 table gives an STI minor diameter of 0.7716 to 0.7838 in and suggests 25/32 in (0.7812 in), the same drill Albany County Fasteners prints. It sits about 0.0025 in under the maximum. Hartner's insert table, our third source on smaller sizes, stops at 5/8-11, so there is no third figure here.
Albany's oversize table goes both ways from 3/4-10. A stripped 5/8-11 hole can be opened up to 3/4-10 with 21/32 in as the first step, and a stripped 3/4-10 goes up to 7/8-9 with a 49/64 in drill.
3/4-10 roll and form taps
Balax and Jarvis both give 45/64 in (0.7031 in) for a forming tap, and Haas gives 17.9 mm (0.7047 in).
FAQ
What is the 3/4-10 tap drill size?
3/4-10 tap drill size is 21/32 in (0.6562 in, 16.67 mm), for about 72% thread inside class 2B.
Is 41/64 OK for 3/4-10?
Not for class 2B. Champion lists 41/64 in first, but at 0.6406 in it is 0.0014 in under the 2B minimum and would cut about 84% thread.
What metric drill for 3/4-10?
16.5 mm, as Hartner prints, gives about 77% thread. 16.4 to 16.8 mm all pass 2B; 17.0 mm, from Engineering Toolbox, is 0.0063 in over.
Can I use the M20 drill for 3/4-10?
No. 17.5 mm (0.6890 in) is 0.0260 in over the 3/4-10 2B maximum. M20 is a different thread, and 21/32 in is too small for it.
What drill for a 3/4-10 Helicoil?
25/32 in (0.7812 in). AmesWeb and Albany County Fasteners agree, and it sits inside the STI hole of 0.7716 to 0.7838 in.
Related pages
Cite or reuse this data
Please quote these figures with a link to this page: TapDrillSize, "3/4-10 tap drill size", https://tapdrillsize.com/3-4-10-tap-drill-size/, published November 25, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.
Chart drills from American Fastener, Little Machine Shop, Starrett, Bolt Depot, Champion Cutting Tool, Emuge, Hartner (Gühring group) and Engineering Toolbox. Class 2B limits and the thread percentage formula from the OSG chart. M20 6H limits from Emuge and Hartner (Gühring group). STI limits and drills from AmesWeb and Albany County Fasteners, oversize repairs from Albany. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on November 25, 2026.