1/2-13 Tap Drill Size
1/2-13 tap drill size is 27/64 in (0.4219 in, 10.72 mm). American Fastener, Little Machine Shop, Starrett, Bolt Depot and Champion Cutting Tool print 27/64 in, and Emuge gives the same hole as a decimal. It leaves about 78% thread inside the class 2B limits of 0.417 to 0.434 in from the OSG chart.
1/2-13 is the coarse (UNC) half-inch thread, 13 threads per inch. The tap drill is settled, but two less obvious numbers on this size are not: one chart's metric drill falls outside 2B, and for a Helicoil insert no common inch drill fits at all.
What eight charts print for 1/2-13
| Chart | Kind | Drill | Diameter | Thread | 2B |
|---|---|---|---|---|---|
| American Fastener | Fastener supplier | 27/64 in | 0.4219 in | 78% | Inside |
| Little Machine Shop | Tool supplier | 27/64 in | 0.4219 in | 78% | Inside |
| Starrett | Tool maker | 27/64 in | 0.4219 in | 78% | Inside |
| Bolt Depot | Fastener supplier | 27/64 in | 0.4219 in | 78% | Inside |
| Champion Cutting Tool | Tool maker | 27/64 in or 11.0 mm | 0.4219 / 0.4331 in | 78% / 67% | Inside |
| Emuge | Tap maker | 0.4219 in (27/64) | 0.4219 in | 78% | Inside |
| Hartner (Gühring group) | Drill maker | 10.8 mm | 0.4252 in | 75% | Inside |
| Engineering Toolbox | Reference site | 11.15 mm | 0.4390 in | 61% | 0.0050 in over |
Six charts agree on 27/64 in. Engineering Toolbox's 11.15 mm is the one outside 2B, by 0.0050 in. Champion's second drill, 11.0 mm, just passes with 0.0009 in to spare, and its own "probable percentage" figures, 75% for 27/64 in and 64% for 11.0 mm, run about 3 points under the formula's 78% and 67%.
Every drill near 27/64 in
Diameters from Wikipedia, thread percentage from the OSG formula: (0.500 − hole) / (1.299 / 13). Class 2B allows about 66% to 83% thread on 1/2-13.
| Drill | Diameter | Thread left | Class 2B |
|---|---|---|---|
| Letter Z | 0.4130 in (10.49 mm) | 87% | Under the min by 0.0040 in |
| 10.55 mm | 0.4154 in | 85% | Under the min by 0.0016 in |
| 10.6 mm | 0.4173 in | 83% | Inside |
| 10.7 mm | 0.4213 in | 79% | Inside |
| 27/64 in | 0.4219 in (10.72 mm) | 78% | Inside |
| 10.8 mm | 0.4252 in | 75% | Inside |
| 10.9 mm | 0.4291 in | 71% | Inside |
| 11.0 mm | 0.4331 in | 67% | Inside |
| 11.05 mm | 0.4350 in | 65% | Over the max by 0.0010 in |
| 7/16 in | 0.4375 in (11.11 mm) | 63% | Over the max by 0.0035 in |
| 11.15 mm | 0.4390 in | 61% | Over the max by 0.0050 in |
27/64 in is the only inch drill inside the band, so the metric steps are the fallback. 10.8 mm sits close to a 75% thread, and 10.9 or 11.0 mm eases the tap in steel.
The 1/2-13 Helicoil problem
AmesWeb, working from ASME B18.29.1, gives an STI hole of 0.5166 to 0.5273 in for 1/2-13 and suggests 33/64 in. But 33/64 in is 0.5156 in, 0.0010 in under that minimum, so the drill AmesWeb suggests is just outside its own limits. Albany County Fasteners prints 17/32 in (0.5313 in), 0.0040 in over the maximum. The two disagree, and neither drill lands inside. A third source settles it: Hartner's insert table gives a metric 13.30 mm drill (0.5236 in), with the same hole limits in millimetres, 13.122 to 13.393 mm. That is inside, and so is 13.25 mm (0.5217 in), close to AmesWeb's 0.5219 in midpoint.
1/2-20 and M12
The fine 1/2-20 takes 29/64 in. The metric M12 is 0.7 mm smaller, and its 10.2 mm drill is 0.0154 in under the 1/2-13 2B minimum; going the other way, 27/64 in is over the M12 6H maximum. No drill serves both.
1/2-13 roll and form taps
A forming tap needs about 0.465 in. Balax gives 0.463 in, Jarvis gives the hole as 0.4660 in without naming a drill, and Haas prints 11.8 mm (0.4646 in).
FAQ
What is the 1/2-13 tap drill size?
1/2-13 tap drill size is 27/64 in (0.4219 in, 10.72 mm), for about 78% thread inside class 2B.
What metric drill for 1/2-13?
10.7 mm is closest to 27/64 in. Hartner prints 10.8 mm (about 75%), Champion also gives 11.0 mm (67%). Both pass. Engineering Toolbox's 11.15 mm is 0.0050 in over the 2B maximum.
Is 7/16 OK for 1/2-13?
No. 7/16 in (0.4375 in) is 0.0035 in over the class 2B maximum and leaves only about 63% thread.
Can I use the M12 drill for 1/2-13?
No. 10.2 mm (0.4016 in) is 0.0154 in under the 1/2-13 2B minimum.
What drill for a 1/2-13 Helicoil?
No common inch drill fits: the STI hole is 0.5166 to 0.5273 in (AmesWeb, ASME B18.29.1). 33/64 in is 0.0010 in under that and 17/32 in is 0.0040 in over. Hartner gives a metric 13.30 mm drill, which fits.
Related pages
Cite or reuse this data
Please quote these figures with a link to this page: TapDrillSize, "1/2-13 tap drill size", https://tapdrillsize.com/1-2-13-tap-drill-size/, published November 22, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.
Chart drills from American Fastener, Little Machine Shop, Starrett, Bolt Depot, Champion Cutting Tool, Emuge, Hartner (Gühring group) and Engineering Toolbox. Class 2B limits and the thread percentage formula from the OSG chart. STI limits and drills from AmesWeb and Albany County Fasteners. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on November 22, 2026.