#6-32 Tap Drill Size
#6-32 tap drill size is a #36 drill, 0.1065 in (2.71 mm). American Fastener, Little Machine Shop, Starrett and Champion Cutting Tool print #36. It leaves about 78% thread and falls inside the class 2B limits of 0.104 to 0.114 in from the OSG chart.
#6-32 is the coarse thread on a #6 screw, 0.138 in across with 32 threads per inch. Its 2B band is wider than on the larger screws: it spans about 59% to 84% thread, so the charts can disagree on the drill and still all be right.
Eight charts, five drills, all inside
| Chart | Kind | Prints | Diameter | Thread | 2B |
|---|---|---|---|---|---|
| American Fastener | Fastener supplier | #36 | 0.1065 in | 78% | Inside |
| Little Machine Shop | Tool supplier | #36 | 0.1065 in | 78% | Inside |
| Starrett | Tool maker | #36 | 0.1065 in | 78% | Inside |
| Champion Cutting Tool | Tool maker | #36 or 7/64 in | 0.1065 / 0.1094 in | 78% / 71% | Inside |
| Bolt Depot | Fastener supplier | #35 or 7/64 in | 0.1100 / 0.1094 in | 69% / 71% | Inside |
| Emuge | Tap maker | 0.1110 in (#34) | 0.1110 in | 67% | Inside |
| Hartner (Gühring group) | Drill maker | 2.85 mm | 0.1122 in | 64% | Inside |
| Engineering Toolbox | Reference site | 2.85 mm | 0.1122 in | 64% | Inside |
Bolt Depot does not print #36 at all; it gives #35 or 7/64 in. Emuge prints the decimal 0.1110 in, which is a #34. The two metric charts go to 2.85 mm, 0.0018 in under the maximum. That is a 14-point spread in thread percentage, 78% down to 64%, with every source still inside 2B. Champion's own "probable percentage" figures, 72% for #36 and 64% for 7/64 in, run 6 to 7 points under the formula's 78% and 71%.
Eleven drills pass on #6-32
Inch and metric drills in this range, diameters from Wikipedia, thread percentage from the OSG formula: (0.138 − hole) / (1.299 / 32).
| Drill | Diameter | Thread left | Class 2B |
|---|---|---|---|
| #38 | 0.1015 in (2.58 mm) | 90% | Under the min by 0.0025 in |
| 2.6 mm | 0.1024 in | 88% | Under the min by 0.0016 in |
| #37 | 0.1040 in (2.64 mm) | 84% | Inside |
| 2.65 mm | 0.1043 in | 83% | Inside |
| 2.7 mm | 0.1063 in | 78% | Inside |
| #36 | 0.1065 in (2.71 mm) | 78% | Inside |
| 2.75 mm | 0.1083 in | 73% | Inside |
| 7/64 in | 0.1094 in (2.78 mm) | 71% | Inside |
| #35 | 0.1100 in (2.79 mm) | 69% | Inside |
| 2.8 mm | 0.1102 in | 68% | Inside |
| #34 | 0.1110 in (2.82 mm) | 67% | Inside |
| 2.85 mm | 0.1122 in | 64% | Inside |
| #33 | 0.1130 in (2.87 mm) | 62% | Inside |
| 2.9 mm | 0.1142 in | 59% | Over the max by 0.0002 in |
| #32 | 0.1160 in (2.95 mm) | 54% | Over the max by 0.0020 in |
Everything from #37 to #33 passes, eleven drills in all. #37 sits right on the 2B minimum, so it is the fullest thread allowed; #33, the standard drill for the fine #6-40, is the easiest on the tap. Every drill between them leaves less thread than the one before and still passes 2B.
#6-32 in computers
Wikipedia's computer case screws article says #6-32 UNC screws are common on 3.5-inch hard drives and on the case body to hold the covers, while 2.5-inch drives use metric M3 screws. If you are tapping a drive bracket or a case panel to take those screws, it is this thread and the #36 drill.
Helicoil (STI) drill for #6-32
A thread insert needs a bigger hole and an STI tap. AmesWeb, working from ASME B18.29.1, gives STI hole limits of 0.1448 to 0.1527 in and a #25 drill (0.1495 in) for #6-32. Albany County Fasteners prints #27 (0.144 in) for the same insert, 0.0008 in under the STI minimum. The two sources disagree; #25 is the one inside the limits. Hartner's insert table, a third source, gives 3.80 mm (0.1496 in) and hole limits of 3.678 to 3.879 mm, the same range as AmesWeb's in millimetres.
#6-32 roll and form taps
Balax and Haas print 3.1 mm (0.1220 in) for a #6-32 forming tap. Jarvis gives the hole as 0.1243 in without naming a drill, so the three are 0.0023 in apart.
FAQ
What is the #6-32 tap drill size?
#6-32 tap drill size is a #36 drill, 0.1065 in (2.71 mm), for about 78% thread inside class 2B.
Is 7/64 OK for #6-32?
Yes. 7/64 in (0.1094 in) leaves about 71% thread and is well inside class 2B. Bolt Depot and Champion print it.
What metric drill for #6-32?
2.7 mm is closest to #36. Hartner and Engineering Toolbox print 2.85 mm, which leaves about 64% and also passes.
What thread are hard drive screws?
3.5-inch hard drives and many case panels use #6-32 UNC, according to Wikipedia's computer case screws article.
What drill for a #6-32 Helicoil?
A #25 (0.1495 in), per AmesWeb's ASME B18.29.1 table. A chart printing #27 for this insert is 0.0008 in under the STI minimum.
Related pages
Cite or reuse this data
Please quote these figures with a link to this page: TapDrillSize, "#6-32 tap drill size", https://tapdrillsize.com/6-32-tap-drill-size/, published November 11, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.
Chart drills from American Fastener, Little Machine Shop, Starrett, Champion Cutting Tool, Bolt Depot, Emuge, Hartner (Gühring group) and Engineering Toolbox. Class 2B limits and the thread percentage formula from the OSG chart. Drive screw threads from Wikipedia. STI limits and drills from AmesWeb and Albany County Fasteners. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on November 11, 2026.