7/16-20 Tap Drill Size
7/16-20 tap drill size is 25/64 in (0.3906 in, 9.92 mm). It leaves about 72% thread inside the class 2B hole limits of 0.383 to 0.395 in from the OSG chart. Four of the eight charts we read give only 25/64 in, Champion gives letter W and then 25/64 in, and three give 9.9 mm, a hole only 0.0009 in smaller (Emuge prints it as 0.3898 in).
7/16-20 is the fine (UNF) 7/16 in thread, 20 threads per inch. Its 2B band is 0.012 in wide, and every chart's drill passes. The numbers that disagree on this size are for the thread insert.
Eight charts for 7/16-20
| Chart | Kind | Drill | Diameter | Thread | 2B |
|---|---|---|---|---|---|
| American Fastener | Fastener supplier | 25/64 in | 0.3906 in | 72% | Inside |
| Little Machine Shop | Tool supplier | 25/64 in | 0.3906 in | 72% | Inside |
| Starrett | Tool maker | 25/64 in | 0.3906 in | 72% | Inside |
| Bolt Depot | Fastener supplier | 25/64 in | 0.3906 in | 72% | Inside |
| Champion Cutting Tool | Tool maker | W, then 25/64 in | 0.3860 / 0.3906 in | 79% / 72% | Inside |
| Emuge | Tap maker | 0.3898 in (9.9 mm) | 0.3898 in | 73% | Inside |
| Hartner (Gühring group) | Drill maker | 9.9 mm | 0.3898 in | 73% | Inside |
| Engineering Toolbox | Reference site | 9.9 mm | 0.3898 in | 73% | Inside |
Champion again leads with the tighter hole. Its letter W leaves about 79% thread by the OSG formula, and Champion's own "probable percentage" puts it at 75%, with 68% for 25/64 in.
7/16-20 drills from 9.7 mm to letter X
Thread left is (0.4375 − hole) / (1.299 / 20). Class 2B on 7/16-20 spans about 65% to 84% thread. Diameters from Wikipedia.
| Drill | Diameter | Thread left | Class 2B |
|---|---|---|---|
| 9.7 mm | 0.3819 in | 86% | Under the min by 0.0011 in |
| 9.75 mm | 0.3839 in | 83% | Inside |
| Letter W | 0.3860 in (9.80 mm) | 79% | Inside |
| 9.85 mm | 0.3878 in | 77% | Inside |
| 9.9 mm | 0.3898 in | 73% | Inside |
| 25/64 in | 0.3906 in (9.92 mm) | 72% | Inside |
| 9.95 mm | 0.3917 in | 70% | Inside |
| 10.0 mm | 0.3937 in | 67% | Inside |
| 10.05 mm | 0.3957 in | 64% | Over the max by 0.0007 in |
| Letter X | 0.3970 in (10.08 mm) | 62% | Over the max by 0.0020 in |
In inch sets only two drills pass, letter W and 25/64 in. Letter X, the next one up, is 0.0020 in over. In metric, 9.75 to 10.0 mm all pass, so a 10 mm drill from any set will do, at about 67% thread.
7/16-20 UNJF
For the rounded-root UNJF thread, Hartner gives 10.00 mm, with class 3B limits of 9.876 to 10.084 mm. 25/64 in (9.922 mm) and 9.9 mm both fall inside that band as well as inside UNF 2B. Champion's letter W does not: at 9.804 mm it is 0.072 mm under the UNJF minimum.
7/16-20 Helicoil drill
AmesWeb's ASME B18.29.1 table gives an STI minor diameter of 0.4483 to 0.4561 in and suggests 29/64 in (0.4531 in). Hartner's insert table gives 11.50 mm (0.4528 in), with limits of 11.389 to 11.585 mm. The two agree.
Albany County Fasteners lists 27/64 in (0.4219 in) for its 7/16-20 STI row, 0.0264 in under that minimum. It is not the plain tap drill either; it sits between the two. The sources disagree, and Albany's figure fits neither the tap drill nor the insert hole. Use 29/64 in, the same drill that taps 1/2-20.
7/16-20 roll and form taps
Balax gives letter Z (0.413 in) or 10.5 mm. Haas also gives 10.5 mm (0.4134 in), and Jarvis gives the hole as 0.4154 in.
FAQ
What is the 7/16-20 tap drill size?
7/16-20 tap drill size is 25/64 in (0.3906 in, 9.92 mm), for about 72% thread inside class 2B.
What metric drill for 7/16-20?
9.9 mm (about 73%), which three of the eight charts give. Anything from 9.75 to 10.0 mm passes 2B.
Is letter W OK for 7/16-20?
Yes for class 2B. W (0.386 in) is Champion's first choice and leaves about 79% thread. It is too small for 7/16-20 UNJF.
What drill for a 7/16-20 Helicoil?
29/64 in (0.4531 in), per AmesWeb, or 11.50 mm per Hartner. Albany County Fasteners prints 27/64 in, which is 0.0264 in under the STI minimum.
Does 7/16-20 take the same drill as 7/16-14?
No. 7/16-14 takes letter U (0.368 in), which is 0.015 in under the 7/16-20 2B minimum.
Related pages
Cite or reuse this data
Please quote these figures with a link to this page: TapDrillSize, "7/16-20 tap drill size", https://tapdrillsize.com/7-16-20-tap-drill-size/, published December 5, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.
Chart drills from American Fastener, Little Machine Shop, Starrett, Bolt Depot, Champion Cutting Tool, Emuge, Hartner (Gühring group) and Engineering Toolbox. Class 2B limits and the thread percentage formula from the OSG chart. UNJF and insert limits from Hartner (Gühring group). STI limits and drills from AmesWeb and Albany County Fasteners. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on December 5, 2026.