#4-40 Tap Drill Size
#4-40 tap drill size is a #43 drill, 0.089 in (2.26 mm). American Fastener, Little Machine Shop and Starrett print #43, and so does Bolt Depot. It leaves about 71% thread inside the class 2B limits of 0.0849 to 0.0939 in from the OSG chart.
#4-40 is a small screw, 0.112 in (2.84 mm) across with 40 threads per inch. Some guides suggest leaving less thread on small taps like this one, and on #4-40 that advice runs into the class 2B limit.
Where the small-tap advice meets class 2B
ToolGrit lists 50 to 55% thread for blind holes in stainless, titanium and hardened steel, and for small taps, which it gives as #6 and below (its FAQ says under #6). Class 2B on #4-40 allows from about 56% to 83% thread. So the whole 50 to 55% range sits just under the 2B floor: a hole cut for it is slightly too big for the 2B minor-diameter limit.
The nearest drills to that advice that still pass are #42 (57%) and 3/32 in (56%). 3/32 in clears the 2B maximum by only 0.00015 in, so treat it as the absolute limit; #42 leaves a little more margin. Below 56%, the hole is out of class 2B however strong the thread is.
What eight charts print for #4-40
| Chart | Kind | Drill | Diameter | Thread | 2B |
|---|---|---|---|---|---|
| American Fastener | Fastener supplier | #43 | 0.0890 in | 71% | Inside |
| Little Machine Shop | Tool supplier | #43 | 0.0890 in | 71% | Inside |
| Starrett | Tool maker | #43 | 0.0890 in | 71% | Inside |
| Bolt Depot | Fastener supplier | #43 or 3/32 in | 0.0890 / 0.0938 in | 71% / 56% | Inside |
| Champion Cutting Tool | Tool maker | #44 or #43 | 0.0860 / 0.0890 in | 80% / 71% | Inside |
| Emuge | Tap maker | 0.0890 in (#43) | 0.0890 in | 71% | Inside |
| Hartner (Gühring group) | Drill maker | 2.35 mm | 0.0925 in | 60% | Inside |
| Engineering Toolbox | Reference site | 2.35 mm | 0.0925 in | 60% | Inside |
Every drill in print passes. The spread is still wide, 80% to 56%, because the charts pick different drills. Champion lists the smaller #44 first, and its own "probable percentage" figures, 74% for #44 and 65% for #43, are about 6 points under the formula's. The two metric charts, at 2.35 mm, leave about 60%, closer to the small-tap advice.
Every drill near #43
Diameters from Wikipedia, thread percentage from the OSG formula: (0.112 − hole) / (1.299 / 40).
| Drill | Diameter | Thread left | Class 2B |
|---|---|---|---|
| 2.15 mm | 0.0846 in | 84% | Under the min by 0.0003 in |
| #44 | 0.0860 in (2.18 mm) | 80% | Inside |
| 2.2 mm | 0.0866 in | 78% | Inside |
| 2.25 mm | 0.0886 in | 72% | Inside |
| #43 | 0.0890 in (2.26 mm) | 71% | Inside |
| 2.3 mm | 0.0906 in | 66% | Inside |
| 2.35 mm | 0.0925 in | 60% | Inside |
| #42 | 0.0935 in (2.37 mm) | 57% | Inside |
| 3/32 in | 0.0938 in (2.38 mm) | 56% | Inside |
| 2.4 mm | 0.0945 in | 54% | Over the max by 0.0006 in |
| #41 | 0.0960 in (2.44 mm) | 49% | Over the max by 0.0021 in |
Eight drills pass, from #44 to 3/32 in. On a thread this fine, one 0.05 mm step moves the thread by about 6 points, so the drill choice matters more than on bigger screws.
The thread in D-sub jackscrews
The jackscrews that hold D-subminiature connectors together are usually #4-40 UNC. The 3M 3342 series jackscrew, for example, is listed with a #4-40 UNC thread. If you are tapping a panel or bracket to take these, it is the same #43 drill.
Helicoil (STI) drill for #4-40
A #4-40 insert hole is only 0.0077 in wide in tolerance: 0.1175 to 0.1252 in, per ASME B18.29.1 as tabled by AmesWeb. A #31 (0.120 in) fits it. The #32 printed by Albany County Fasteners, 0.116 in, does not; it is 0.0015 in small, one number drill too far.
#4-40 roll and form taps
For a forming tap, Balax, Jarvis and Haas all give a #39 drill (0.0995 in).
FAQ
What is the #4-40 tap drill size?
#4-40 tap drill size is a #43 drill, 0.089 in (2.26 mm), for about 71% thread inside class 2B.
Is 3/32 OK for #4-40?
Yes, just. 3/32 in (0.0938 in) leaves about 56% thread and is only 0.00015 in under the 2B maximum. Bolt Depot lists it.
Should I use 50% thread on #4-40?
Not if the drawing calls for class 2B. ToolGrit lists 50 to 55% for small taps and for blind holes in tough metals, but 2B on #4-40 needs at least about 56%, so a 50% hole is out of class.
What metric drill for #4-40?
2.25 mm is closest to #43. Hartner and Engineering Toolbox print 2.35 mm, about 60% thread, which also passes.
What drill for a #4-40 Helicoil?
A #31 (0.120 in), per AmesWeb's ASME B18.29.1 table. A chart printing #32 for this insert is 0.0015 in under the STI minimum.
Related pages
Cite or reuse this data
Please quote these figures with a link to this page: TapDrillSize, "#4-40 tap drill size", https://tapdrillsize.com/4-40-tap-drill-size/, published November 16, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.
Chart drills from American Fastener, Little Machine Shop, Starrett, Bolt Depot, Champion Cutting Tool, Emuge, Hartner (Gühring group) and Engineering Toolbox. Class 2B limits and the thread percentage formula from the OSG chart. Small-tap thread range from ToolGrit. Jackscrew thread from RS Components. STI limits and drills from AmesWeb and Albany County Fasteners. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on November 16, 2026.