M10 Tap Drill Size
M10 tap drill size is 8.5 mm (0.335 in) for the standard M10 x 1.5 coarse thread. Starrett, Champion Cutting Tool, Emuge and Hartner (Gühring group) all print 8.5 mm. That gives about 77% thread, and the hole falls inside class 6H, 8.376 to 8.676 mm.
On M10 the pitch matters as much as the size. The same 10 mm diameter comes in four pitches in the Hartner chart, and each takes its own drill. A plain "M10" means the 1.5 mm coarse one, since the coarse pitch can be left off the name (Wikipedia).
One diameter, four pitches, four drills
Drills and class 6H limits from the Hartner chart:
| Thread | Tap drill | 6H hole limits | Threads in 15 mm |
|---|---|---|---|
| M10 x 1.5 (coarse) | 8.5 mm | 8.376 to 8.676 mm | 10 |
| M10 x 1.25 | 8.8 mm | 8.647 to 8.912 mm | 12 |
| M10 x 1 | 9.0 mm | 8.917 to 9.153 mm | 15 |
| M10 x 0.75 | 9.2 mm | 9.188 to 9.378 mm | 20 |
The coarse and M10 x 1.25 bands overlap by 0.029 mm, between 8.647 and 8.676 mm, so a hole in that sliver passes 6H for both. No drill in the usual 0.1 mm or inch series lands there, though: 8.6 mm is too small for M10 x 1.25 and 8.7 mm is too big for coarse M10. To tell the screws apart, count threads over 15 mm with a ruler, or use a pitch gauge.
What five charts print for M10
| Published by | Kind of company | Drill printed | Thread | 6H check |
|---|---|---|---|---|
| Starrett | Tool maker | 8.5 mm | 77% | Inside |
| Champion Cutting Tool | Tool maker | 8.5 mm | 77% | Inside |
| Emuge | Tap maker | 8.5 mm | 77% | Inside |
| Hartner (Gühring group) | Drill maker | 8.5 mm | 77% | Inside |
| Bolt Depot | Fastener supplier | 8.7 mm | 67% | Over the max by 0.024 mm |
Bolt Depot is the outlier: its 8.7 mm leaves about 67% thread by the OSG formula and is 0.024 mm over the 6H maximum. A drill one step smaller, 8.6 mm, leaves about 72% and passes: the biggest 0.1 mm metric step inside 6H. Letter R, 8.611 mm, passes too and cuts slightly less.
M10 with letter, fractional and metric drills
Diameters from Wikipedia:
| Drill | Diameter | Thread left | Class 6H |
|---|---|---|---|
| Letter P | 8.204 mm (0.323 in) | 92% | Under the min by 0.172 mm |
| 8.3 mm | 8.300 mm | 87% | Under the min by 0.076 mm |
| 21/64 in | 8.334 mm (0.3281 in) | 86% | Under the min by 0.042 mm |
| 8.4 mm | 8.400 mm | 82% | Inside |
| Letter Q | 8.433 mm (0.332 in) | 80% | Inside |
| 8.5 mm | 8.500 mm | 77% | Inside |
| 8.6 mm | 8.600 mm | 72% | Inside |
| Letter R | 8.611 mm (0.339 in) | 71% | Inside |
| 8.7 mm | 8.700 mm | 67% | Over the max by 0.024 mm |
| 11/32 in | 8.731 mm (0.3438 in) | 65% | Over the max by 0.055 mm |
| Letter S | 8.839 mm (0.348 in) | 60% | Over the max by 0.163 mm |
No fractional drill passes: 21/64 in is too small and 11/32 in too big. Letters Q and R are the inch choices, Q for a fuller thread and R for an easier cut.
M10 vs 3/8-16
3/8-16, the nearest inch thread, is 9.53 mm across with a 1.588 mm pitch. Its standard 5/16 in drill is 7.94 mm, 0.438 mm under the M10 6H minimum. In an M10 hole that would mean cutting about 106% of a thread, far more than the tap is made to cut, so expect it to bind or break. The two screws are not interchangeable either.
Depth and roll taps
For a blind M10 hole, add at least 4 threads, 6 mm on this pitch, below the thread you need (ToolGrit). A 10 mm thread then needs a 16 mm deep hole, and a 15 mm thread a 21 mm one. ToolGrit's strength figures assume a thread at least 1 to 1.5 times the diameter long, 10 to 15 mm here.
Roll taps form the thread without chips and start from 9.3 mm on M10, the size Balax, Jarvis and Haas agree on. That is 0.8 mm above the cutting drill, and the two are not interchangeable.
FAQ
What is the M10 tap drill size?
M10 tap drill size is 8.5 mm (0.335 in) for the standard M10 x 1.5 coarse thread, about 77% thread and inside class 6H.
Is 8.7 mm OK for M10?
Not for class 6H. Bolt Depot prints 8.7 mm, but the hole is 0.024 mm over the 6H maximum of 8.676 mm. 8.6 mm is the biggest 0.1 mm step that passes.
What inch drill can I use for M10?
A letter Q (0.332 in, 8.433 mm) for about 80% thread, or a letter R (0.339 in, 8.611 mm) for about 71%. Both pass 6H.
Can I use the 3/8-16 drill for M10?
No. 3/8-16 takes a 5/16 in drill, 7.94 mm. That is 0.438 mm under the M10 6H minimum, far too small for an M10 tap.
How big a hole does an M10 roll tap need?
9.3 mm, from the Balax, Jarvis and Haas charts.
Related pages
Cite or reuse this data
Please quote these figures with a link to this page: TapDrillSize, "M10 tap drill size", https://tapdrillsize.com/m10-tap-drill-size/, published November 4, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.
Chart drills from Starrett, Champion Cutting Tool, Emuge, Hartner (Gühring group) and Bolt Depot. Class 6H limits from Emuge and Hartner (Gühring group), fine pitch drills and limits from Hartner (Gühring group). Thread percentage formula from the OSG chart. Thread length and blind hole depth from ToolGrit. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on November 4, 2026.