#0-80 Tap Drill Size
#0-80 tap drill size is 3/64 in (0.0469 in, 1.19 mm). Five of the seven charts we read that list #0-80 print 3/64 in, and it leaves about 81% thread inside the class 2B hole limits of 0.0465 to 0.0514 in from the OSG chart.
#0-80 is the smallest screw on this site: 0.060 in (1.52 mm) across with 80 threads per inch, a 0.3175 mm pitch. The Unified series gives #0 only this one fine pitch, so it is a UNF thread with no coarse partner. At this size the hole is so small that one number drill step can move a hole from inside 2B to outside it.
Seven charts for #0-80
| Chart | Kind | Drill | Diameter | Thread | 2B |
|---|---|---|---|---|---|
| American Fastener | Fastener supplier | 3/64 in | 0.0469 in | 81% | Inside |
| Little Machine Shop | Tool supplier | 3/64 in | 0.0469 in | 81% | Inside |
| Starrett | Tool maker | 3/64 in | 0.0469 in | 81% | Inside |
| Bolt Depot | Fastener supplier | 3/64 in | 0.0469 in | 81% | Inside |
| Champion Cutting Tool | Tool maker | #56, then 3/64 in | 0.0465 / 0.0469 in | 83% / 81% | Inside (#56 at the minimum) |
| Emuge | Tap maker | 0.0480 in (a hole size) | 0.0480 in | 74% | Inside |
| Engineering Toolbox | Reference site | 1.25 mm | 0.0492 in | 66% | Inside |
All seven pass, but they don't all cut the same thread. From Champion's #56 to Engineering Toolbox's 1.25 mm the thread drops from about 83% to 66%. Emuge gives a hole diameter, not a drill: 0.0480 in, 1.22 mm, sits between 1.2 and 1.25 mm. Hartner (Gühring group)'s chart, the eighth we use, starts its fine inch rows at #1-72 and has no #0. Champion rates its own two drills at a "probable" 74% and 71%, about 9 to 10 points under the OSG formula.
#0-80 drills from #57 to 1.35 mm
Thread left is (0.060 − hole) / (1.299 / 80). Class 2B on #0-80 allows about 53% to 83% thread. Diameters from Wikipedia.
| Drill | Diameter | Thread left | Class 2B |
|---|---|---|---|
| #57 | 0.0430 in (1.09 mm) | 105% | Under the min by 0.0035 in |
| 1.15 mm | 0.0453 in | 91% | Under the min by 0.0012 in |
| #56 | 0.0465 in (1.18 mm) | 83% | Inside |
| 3/64 in | 0.0469 in (1.19 mm) | 81% | Inside |
| 1.2 mm | 0.0472 in | 79% | Inside |
| 1.25 mm | 0.0492 in | 66% | Inside |
| 1.3 mm | 0.0512 in | 54% | Inside |
| #55 | 0.0520 in (1.32 mm) | 49% | Over the max by 0.0006 in |
| 1.35 mm | 0.0531 in | 42% | Over the max by 0.0017 in |
#57 comes out over 100% on the formula, far too small. The jump from #56 to #55 is 0.0055 in, more than the whole 2B band of 0.0049 in, so #56, right at the minimum, is the only number drill inside it. Metric sizes fill that gap: 1.2, 1.25 and 1.3 mm all pass, and 1.3 mm is inside by only 0.0002 in.
Champion's #56 on the edge
#56 is 0.0465 in, exactly the class 2B minimum minor diameter. A drill that cuts at its nominal size leaves a hole right on the limit, and one that cuts even slightly undersize takes it out of class. 3/64 in, which the other charts print, is 0.0004 in bigger. If #56 is the only small drill you have, the hole is in class with nothing to spare.
#0-80 form taps and inserts
For a forming tap, Balax gives #54 (0.055 in) or 1.4 mm (0.0551 in), and Jarvis also gives #54. The Haas forming chart has no #0 row. None of the three insert sources we compare, AmesWeb, Albany County Fasteners and Hartner, list a #0-80 insert; AmesWeb's table starts at #1-64.
FAQ
What is the #0-80 tap drill size?
#0-80 tap drill size is 3/64 in (0.0469 in, 1.19 mm), for about 81% thread inside class 2B.
What metric drill for #0-80?
1.2 mm (about 79%) is the closest to 3/64 in. 1.25 mm, which Engineering Toolbox prints, leaves about 66%, and 1.3 mm about 54%. All three pass class 2B.
Is #56 OK for #0-80?
Only just. Champion prints #56 (0.0465 in), which is exactly the class 2B minimum, at about 83% thread. 3/64 in is a safer hole.
Is #55 OK for #0-80?
No. #55 (0.052 in) is 0.0006 in over the 2B maximum and leaves only about 49% thread.
Is there a #0 coarse thread?
No. #0 has only the fine 80 threads per inch in the Unified series, so #0-80 is always UNF.
Related pages
Cite or reuse this data
Please quote these figures with a link to this page: TapDrillSize, "#0-80 tap drill size", https://tapdrillsize.com/0-80-tap-drill-size/, published December 2, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.
Chart drills from American Fastener, Little Machine Shop, Starrett, Bolt Depot, Champion Cutting Tool, Emuge and Engineering Toolbox; Hartner (Gühring group) has no #0 row. Class 2B limits and the thread percentage formula from the OSG chart. Thread series from Wikipedia. Form tap drills from Balax and Jarvis. Drill diameters from Wikipedia. Published on December 2, 2026.