M3 Tap Drill Size

M3 tap drill size is 2.5 mm (0.098 in) for the standard M3 x 0.5 thread. Starrett, Bolt Depot, Champion Cutting Tool, Emuge and Hartner (Gühring group) all print 2.5 mm. It leaves about 77% thread inside the class 6H range of 2.459 to 2.599 mm.

With the drill settled, the questions on M3 are practical ones: which inch drill to use if there is no 2.5 mm in the box, how close 2.6 mm comes, and how to keep a tap this small in one piece.

Five charts, one answer

SourceWhat it isDrillThread6H
StarrettTool maker2.5 mm77%Inside
Bolt DepotFastener supplier2.5 mm77%Inside
Champion Cutting ToolTool maker2.5 mm77%Inside
EmugeTap maker2.5 mm77%Inside
Hartner (Gühring group)Drill maker2.5 mm77%Inside

On every size from M4 to M16, Bolt Depot prints a bigger drill than the other charts. On M3 it agrees with them. 2.5 mm is the major diameter minus the pitch, 3 − 0.5, and the thread percentage comes from the OSG formula, (3 − hole) / (1.299 x 0.5).

Number drills for M3

Diameters from Wikipedia:

DrillDiameterThread leftClass 6H
3/32 in2.381 mm (0.0938 in)95%Under the min by 0.078 mm
#412.438 mm (0.096 in)86%Under the min by 0.021 mm
2.45 mm2.450 mm85%Under the min by 0.009 mm
#402.489 mm (0.098 in)79%Inside
2.5 mm2.500 mm77%Inside
#392.527 mm (0.0995 in)73%Inside
2.55 mm2.550 mm69%Inside
#382.578 mm (0.1015 in)65%Inside
2.6 mm2.600 mm62%Over the max by 0.001 mm
#372.642 mm (0.104 in)55%Over the max by 0.043 mm

Three number drills pass: #40, #39 and #38. #40 is the closest to 2.5 mm, 0.011 mm smaller. 3/32 in, the nearest fractional drill, is far too small.

The 2.6 mm question

A 2.6 mm hole is over the 6H maximum by 0.001 mm. It leaves about 62% thread and is out of class on paper, and a drill that cuts slightly oversize makes it worse. If the part will be gauged, 2.55 mm gives a passing hole with less thread than 2.5 mm, 0.049 mm under the maximum. #38 also passes, but with only 0.021 mm to spare.

M3 also has a fine pitch, M3 x 0.35. The Hartner chart gives it a 2.65 mm drill and 6H limits of 2.621 to 2.721 mm, so a 2.65 mm hole is too big for coarse M3.

M3 in stepper motors

NEMA 17 stepper motors mount on M3 screws in a 31 mm square. One supplier, Evil Mad Scientist, specifies "M3 with 3.5 mm min. thread depth" for its motor. As a worked example of that depth: a blind M3 hole with 3.5 mm of usable thread needs at least 4 extra threads below it, 2 mm on this pitch (ToolGrit), so drill 5.5 mm of full-diameter depth, plus the drill point.

Keeping a small tap in one piece

Common causes of broken taps include clogged flutes, a tap that is not in line with the hole, and too little cutting fluid (Wikipedia). Back the tap off now and then to break the chip, and in a blind hole leave the full 2 mm of extra depth.

A forming tap avoids chips entirely but needs a bigger hole, about 2.8 mm: Balax gives a #35 (2.79 mm), and Jarvis and Haas give 7/64 in (2.78 mm).

FAQ

What is the M3 tap drill size?

M3 tap drill size is 2.5 mm (0.098 in) for the standard M3 x 0.5 thread. All five charts we read print it, and it leaves about 77% thread inside class 6H.

Can I use 2.6 mm for M3?

Not for class 6H. 2.6 mm is 0.001 mm over the 6H maximum of 2.599 mm, so on paper it fails. 2.55 mm is the safe step up.

What number drill for M3?

A #40 (0.098 in, 2.489 mm) is closest to 2.5 mm, at about 79%. #39 and #38 also pass 6H. #41 and 3/32 in are under the minimum.

How deep should I drill a blind M3 hole?

At least 2 mm deeper than the thread you need: 4 threads of 0.5 mm. For 3.5 mm of thread, drill 5.5 mm.

What hole for an M3 roll tap?

About 2.8 mm. Balax gives a #35 (2.79 mm), and Jarvis and Haas give 7/64 in (2.78 mm).

Related pages

Cite or reuse this data

Please quote these figures with a link to this page: TapDrillSize, "M3 tap drill size", https://tapdrillsize.com/m3-tap-drill-size/, published November 10, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.

Chart drills from Starrett, Bolt Depot, Champion Cutting Tool, Emuge and Hartner (Gühring group). Class 6H limits from Emuge and Hartner (Gühring group), and the M3 x 0.35 row from Hartner (Gühring group). Thread percentage formula from the OSG chart. Blind hole depth from ToolGrit, tap breakage from Wikipedia. Motor spec from Evil Mad Scientist. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on November 10, 2026.