M4 Tap Drill Size

M4 tap drill size is 3.3 mm (0.130 in) for the standard M4 x 0.7 thread. Expect about 77% thread, with the hole inside the class 6H range of 3.242 to 3.422 mm given by Emuge and Hartner (Gühring group).

The 6H band on M4 is only 0.18 mm wide, so small drill differences matter here. The metric choices are easy. The inch ones are not: of the number and fractional drills near 3.3 mm, only one passes.

What five charts print for M4

ChartMaker or sellerPrintsThread left6H result
StarrettTool maker3.3 mm77%Inside
Champion Cutting ToolTool maker3.3 mm77%Inside
EmugeTap maker3.3 mm77%Inside
Hartner (Gühring group)Drill maker3.3 mm77%Inside
Bolt DepotFastener supplier3.4 mm66%Inside

Four charts give 3.3 mm, the major diameter minus the pitch. Bolt Depot gives one size bigger, 3.4 mm, which leaves about 66% thread by the OSG formula and is still inside 6H, 0.022 mm under the maximum. On M4 every chart we read passes.

Only one inch drill passes

Number, fractional and metric drills near 3.3 mm, with diameters from Wikipedia:

DrillDiameterThread leftClass 6H
#313.048 mm (0.120 in)105%Under the min by 0.194 mm
1/8 in3.175 mm (0.125 in)91%Under the min by 0.067 mm
3.2 mm3.200 mm88%Under the min by 0.042 mm
#303.264 mm (0.1285 in)81%Inside
3.3 mm3.300 mm77%Inside
3.4 mm3.400 mm66%Inside
#293.454 mm (0.136 in)60%Over the max by 0.032 mm
3.5 mm3.500 mm55%Over the max by 0.078 mm
#283.569 mm (0.1405 in)47%Over the max by 0.147 mm

#30 is the only number drill inside the band, and it leaves a full 81%. The next size up, #29, is over the maximum, and 1/8 in is under the minimum. With an inch-only drill set, #30 is the drill for M4.

M4 and #8-32: a drill that suits both

M4 and #8-32 are close: 4.00 mm against 4.17 mm across, with pitches of 0.70 mm and 0.79 mm. Their standard drills do not cross over. The usual #8-32 drill, #29, is over the M4 maximum, and the M4 drill, 3.3 mm, is 0.002 mm under the #8-32 class 2B minimum of 0.130 in (3.302 mm) from the OSG chart.

One common drill fits both: 3.4 mm. It leaves about 66% thread in M4, inside 6H, and about 74% in #8-32, inside 2B (0.130 to 0.139 in). The screws themselves are still not interchangeable.

The fine pitch, M4 x 0.5

M4 also comes in a 0.5 mm fine pitch. The Hartner chart gives it a 3.5 mm drill and 6H limits of 3.459 to 3.599 mm. That 3.5 mm drill is 0.078 mm over the coarse M4 maximum, so check the pitch before drilling.

Tapping a small hole

Taps usually break when chips clog the flutes, the tap is not in line with the hole, or there is too little cutting fluid (Wikipedia). A 3.4 mm hole leaves the tap less metal to cut than 3.3 mm, at the cost of some thread. For a thread-forming tap, drill 3.7 mm instead. Balax, Jarvis and Haas print the same figure.

FAQ

What is the M4 tap drill size?

M4 tap drill size is 3.3 mm (0.130 in) for the standard M4 x 0.7 thread, about 77% thread and inside class 6H.

Is 3.4 mm OK for M4?

Yes. 3.4 mm leaves about 66% thread and is inside class 6H, 0.022 mm under the maximum. Bolt Depot prints it.

What number drill can I use for M4?

Only a #30 (0.1285 in, 3.264 mm), which leaves about 81% thread. #29 is 0.032 mm over the 6H maximum and #31 is far under the minimum.

Can I use the #8-32 drill for M4?

Not the #29. It is over the M4 6H maximum. A 3.4 mm drill is the one common size inside the limits for both M4 and #8-32.

M4 roll tap: what drill?

3.7 mm, per Balax, Jarvis and Haas. The cutting drill, 3.3 mm, is too small for it.

Related pages

Cite or reuse this data

Please quote these figures with a link to this page: TapDrillSize, "M4 tap drill size", https://tapdrillsize.com/m4-tap-drill-size/, published November 4, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.

Chart drills from Starrett, Champion Cutting Tool, Emuge, Hartner (Gühring group) and Bolt Depot. Class 6H limits from Emuge and Hartner (Gühring group), and the M4 x 0.5 row from Hartner (Gühring group). #8-32 class 2B limits and the thread percentage formula from the OSG chart. Tapping tips from Wikipedia. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on November 4, 2026.