M5 Tap Drill Size

M5 tap drill size is 4.2 mm (0.165 in) for the standard M5 x 0.8 thread. Starrett, Champion Cutting Tool, Emuge and Hartner (Gühring group) print 4.2 mm, which leaves about 77% thread and falls inside the class 6H range of 4.134 to 4.334 mm.

In size, M5 sits between two inch screws: the #10 (4.83 mm) just below it and the #12 (5.49 mm) just above. Unlike M4 and M6, M5 has no common drill it shares with its inch lookalike, which is the main thing to know if you tap both.

Five charts: 4.2 mm, and one 4.3 mm

ChartBusinessDrillThread6H
StarrettTool maker4.2 mm77%Inside
Champion Cutting ToolTool maker4.2 mm77%Inside
EmugeTap maker4.2 mm77%Inside
Hartner (Gühring group)Drill maker4.2 mm77%Inside
Bolt DepotFastener supplier4.3 mm67%Inside

4.2 mm is the major diameter minus the pitch, 5 − 0.8. Bolt Depot's 4.3 mm leaves less thread but still passes, 0.034 mm under the 6H maximum. Thread percentages use the OSG formula: (5 − hole) / (1.299 x 0.8).

M5 and #10-32 share no common drill

#10-32 is 4.83 mm across with a 0.794 mm pitch, almost the same pitch as M5's 0.8 mm. The two hole bands barely touch:

ThreadHole limitsStandard drill
M5 x 0.8 (6H)4.134 to 4.334 mm4.2 mm
#10-32 (2B)3.962 to 4.166 mm#21 (4.039 mm)

The overlap is 4.134 to 4.166 mm, only 0.032 mm wide. 4.1 mm misses M5 and 4.2 mm misses #10-32; on the number side, #20 fits only #10-32 and #19 only M5. A 4.15 mm drill from a 0.05 mm set is the one size inside both: about 82% thread in M5 and 66% in #10-32. That differs from M4, where 3.4 mm works for M4 and #8-32, and M6, where a #7 works for M6 and 1/4-20. The #10-32 limits are 0.156 to 0.164 in from the OSG chart, converted here to mm.

Number and fractional drills for M5

Diameters from Wikipedia:

DrillDiameterThread leftClass 6H
#214.039 mm (0.159 in)93%Under the min by 0.095 mm
#204.089 mm (0.161 in)88%Under the min by 0.045 mm
4.1 mm4.100 mm87%Under the min by 0.034 mm
4.15 mm4.150 mm82%Inside
4.2 mm4.200 mm77%Inside
#194.216 mm (0.166 in)75%Inside
4.25 mm4.250 mm72%Inside
4.3 mm4.300 mm67%Inside
#184.305 mm (0.1695 in)67%Inside
4.35 mm4.350 mm63%Over the max by 0.016 mm
11/64 in4.366 mm (0.1719 in)61%Over the max by 0.032 mm

#19 is a near-perfect inch stand-in for 4.2 mm, 0.016 mm bigger and about 75% thread. No fractional drill passes: 11/64 in is over and 5/32 in is far under.

The fine pitch, M5 x 0.5

The Hartner chart lists M5 x 0.5 with a 4.5 mm drill and 6H limits of 4.459 to 4.599 mm. That drill is 0.166 mm over the coarse M5 maximum, so a 4.5 mm hole is for the fine thread only.

Depth and form taps

For a blind M5 hole, ToolGrit asks for at least 4 threads below the usable thread, 3.2 mm on M5 x 0.8. For 5 mm of thread that means 8.2 mm of full-diameter depth, and for 7.5 mm of thread 10.7 mm, before the drill point. Those lengths, 1 to 1.5 times the diameter, are what ToolGrit's strength figures assume.

A forming tap starts from about 4.6 mm: Balax and Jarvis give a #14 (4.62 mm) and Haas gives 4.6 mm.

FAQ

What is the M5 tap drill size?

M5 tap drill size is 4.2 mm (0.165 in) for the standard M5 x 0.8 thread, about 77% thread and inside class 6H.

Is 4.3 mm OK for M5?

Yes. Bolt Depot prints 4.3 mm. It leaves about 67% thread and is inside 6H, 0.034 mm under the maximum.

What number drill for M5?

A #19 (0.166 in, 4.216 mm), for about 75% thread. #18 also passes, at about 67%. #20 is under the minimum.

Can one drill tap M5 and #10-32?

Not with common sizes. 4.1 mm is too small for M5 and 4.2 mm too big for #10-32. Only a 4.15 mm drill, from a 0.05 mm set, is inside both.

What hole for an M5 form tap?

About 4.6 mm. Balax and Jarvis give a #14 drill (0.182 in, 4.62 mm) and Haas gives 4.6 mm.

Related pages

Cite or reuse this data

Please quote these figures with a link to this page: TapDrillSize, "M5 tap drill size", https://tapdrillsize.com/m5-tap-drill-size/, published November 8, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.

Chart drills from Starrett, Champion Cutting Tool, Emuge, Hartner (Gühring group) and Bolt Depot. Class 6H limits from Emuge and Hartner (Gühring group), and the M5 x 0.5 row from Hartner (Gühring group). #10-32 class 2B limits and the thread percentage formula from the OSG chart. Blind hole depth from ToolGrit. Form tap drills from Balax, Jarvis and Haas. Drill diameters from Wikipedia. Published on November 8, 2026.