M30 Tap Drill Size

M30 tap drill size is 26.5 mm (1.043 in) for the standard M30 x 3.5 coarse thread. Starrett, Champion Cutting Tool, Emuge and Hartner (Gühring group) all print 26.5 mm, and it leaves about 77% thread inside the class 6H range of 26.211 to 26.771 mm.

M30 is the largest size on this site. Its 3.5 mm pitch is the coarsest here. Bolt Depot's metric chart, which we use on smaller sizes, does not list M30, and nor do the form tap and thread insert charts we compare on other pages.

Five M30 pitches in one chart

The Hartner chart lists M30 in five pitches. Each needs its own drill. Only the two coarsest bands touch, and the finer ones are well apart.

ThreadTap drill6H hole limits
M30 x 3.5 (coarse)26.5 mm26.211 to 26.771 mm
M30 x 327.0 mm26.752 to 27.252 mm
M30 x 228.0 mm27.835 to 28.210 mm
M30 x 1.528.5 mm28.376 to 28.676 mm
M30 x 129.0 mm28.917 to 29.153 mm

The coarse and M30 x 3 bands overlap by 0.019 mm, from 26.752 to 26.771 mm, so a hole of about 26.76 mm would pass both. No standard drill lands there. Every finer pitch is a separate band. Each tap drill in the table is the major diameter minus the pitch, which is a quick check for any of them.

Drills for coarse M30

Thread left is (30 − hole) / (1.299 x 3.5), the OSG formula. Class 6H on M30 allows about 71% to 83% thread, a band 0.560 mm wide. Diameters from Wikipedia.

DrillDiameterThread leftClass 6H
26.2 mm26.200 mm84%Under the min by 0.011 mm
1-1/32 in26.194 mm (1.0312 in)84%Under the min by 0.017 mm
26.25 mm26.250 mm82%Inside
26.5 mm26.500 mm77%Inside
1-3/64 in26.591 mm (1.0469 in)75%Inside
26.75 mm26.750 mm71%Inside
26.8 mm26.800 mm70%Over the max by 0.029 mm

26.25 mm is the smallest common size that passes and 26.75 mm the largest. In inches, 1-3/64 in is the one to use; 1-1/32 in, the round number below it, is just too small. On a hole this size each 0.05 mm of drill moves the thread by only about 1 point, so being a few hundredths off changes little.

How big M30 is

Wikipedia's ISO metric thread table puts the spanner size for an M30 hex nut or bolt at 46 mm, in both the ISO and DIN columns, and the hex key for an M30 socket-head cap screw at 22 mm. Basic thread depth on the nut is 0.541266 x pitch, 1.894 mm here, nearly nine times the 0.217 mm of an M2.

FAQ

What is the M30 tap drill size?

M30 tap drill size is 26.5 mm (1.043 in) for the standard M30 x 3.5 coarse thread, about 77% thread inside class 6H.

What inch drill for M30?

1-3/64 in (26.591 mm), about 75% thread, inside 6H. 1-1/32 in is 0.017 mm under the minimum.

What drill for M30 x 2?

28.0 mm, per the Hartner chart, with 6H limits of 27.835 to 28.210 mm. M30 x 1.5 takes 28.5 mm and M30 x 3 takes 27.0 mm.

What spanner fits an M30 bolt?

46 mm across flats for a hex nut or bolt head, and a 22 mm hex key for an M30 socket-head cap screw, per the ISO metric table on Wikipedia.

Is 27 mm OK for coarse M30?

No. 27.0 mm is the drill for M30 x 3. For M30 x 3.5 it is 0.229 mm over the 6H maximum of 26.771 mm.

Related pages

Cite or reuse this data

Please quote these figures with a link to this page: TapDrillSize, "M30 tap drill size", https://tapdrillsize.com/m30-tap-drill-size/, published December 6, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.

Chart drills from Starrett, Champion Cutting Tool, Emuge and Hartner (Gühring group); Bolt Depot's metric chart has no M30 row. Class 6H limits from Emuge and Hartner (Gühring group), fine pitch rows from Hartner (Gühring group). Thread percentage formula from the OSG chart. Spanner and hex key sizes from Wikipedia. Drill diameters from Wikipedia. Published on December 6, 2026.