M22 Tap Drill Size
M22 tap drill size is 19.5 mm (0.768 in) for the standard M22 x 2.5 coarse thread. Starrett, Champion Cutting Tool, Emuge and Hartner (Gühring group) all print 19.5 mm, and it leaves about 77% thread inside the class 6H range of 19.294 to 19.744 mm.
M22 shares its 2.5 mm pitch, and so the width of its 6H band, with M18 and M20. What sets it apart is its inch neighbour. 7/8-9 is 22.225 mm across, and the two threads are close enough in size that one drill set serves both.
Drills for coarse M22
Thread left is (22 − hole) / (1.299 x 2.5), the OSG formula. On M22, 6H spans about 69% to 83% thread. Diameters from Wikipedia.
| Drill | Diameter | Thread left | Class 6H |
|---|---|---|---|
| 19.25 mm | 19.250 mm | 85% | Under the min by 0.044 mm |
| 19.3 mm | 19.300 mm | 83% | Inside |
| 19.4 mm | 19.400 mm | 80% | Inside |
| 49/64 in | 19.447 mm (0.7656 in) | 79% | Inside |
| 19.5 mm | 19.500 mm | 77% | Inside |
| 19.6 mm | 19.600 mm | 74% | Inside |
| 19.7 mm | 19.700 mm | 71% | Inside |
| 19.75 mm | 19.750 mm | 69% | Over the max by 0.006 mm |
Everything from 19.3 to 19.7 mm passes. 19.75 mm is over by 0.006 mm, the same narrow miss as 15.75 mm on M18 and 17.75 mm on M20, because all three have the same pitch and the same band.
One drill set for M22 and 7/8-9
Class 2B for 7/8-9 allows a hole of 0.755 to 0.778 in, 19.177 to 19.761 mm, from the OSG chart. The whole M22 6H band, 19.294 to 19.744 mm, fits inside it. So any hole that passes M22 also passes 7/8-9:
| Drill | On M22 (6H) | On 7/8-9 (2B) |
|---|---|---|
| 49/64 in (the 7/8-9 drill) | 79%, inside | 76%, inside |
| 19.5 mm (the M22 drill) | 77%, inside | 74%, inside |
The other way round is not quite true: 7/8-9 2B starts lower, at 19.177 mm, so a 19.2 or 19.25 mm hole would pass 7/8-9 but not M22. And the threads do not fit each other. 9 threads per inch is a 2.822 mm pitch, against 2.5 mm for M22, so an M22 bolt will not run into a 7/8-9 hole.
M22 pitches in the Hartner chart
| Thread | Tap drill | 6H hole limits |
|---|---|---|
| M22 x 2.5 (coarse) | 19.5 mm | 19.294 to 19.744 mm |
| M22 x 2 | 20.0 mm | 19.835 to 20.210 mm |
| M22 x 1.5 | 20.5 mm | 20.376 to 20.676 mm |
| M22 x 1 | 21.0 mm | 20.917 to 21.153 mm |
From the Hartner chart. For a forming tap on coarse M22, Haas gives 20.9 mm; Balax and Jarvis don't list M22.
Two spanner sizes for M22
M22 is one of the sizes where the two hex standards disagree. Wikipedia's ISO metric table gives 34 mm across flats in its ISO column and 32 mm in its DIN 934 column. The hex key for an M22 socket-head cap screw is 17 mm.
FAQ
What is the M22 tap drill size?
M22 tap drill size is 19.5 mm (0.768 in) for the standard M22 x 2.5 coarse thread, about 77% thread inside class 6H.
What inch drill for M22?
49/64 in (19.447 mm), about 79% thread, inside 6H. It is also the standard drill for 7/8-9.
Can M22 and 7/8-9 use the same drill?
Yes. Every hole inside the M22 6H band, 19.294 to 19.744 mm, is also inside 7/8-9 class 2B, 19.177 to 19.761 mm. The threads themselves are different and do not fit each other.
What drill for M22 x 1.5?
20.5 mm, per the Hartner chart, with 6H limits of 20.376 to 20.676 mm. M22 x 2 takes 20.0 mm.
What spanner fits an M22 nut?
34 mm across flats in the ISO column of Wikipedia's table, 32 mm in the DIN 934 column. Check which standard your nut follows.
Related pages
Cite or reuse this data
Please quote these figures with a link to this page: TapDrillSize, "M22 tap drill size", https://tapdrillsize.com/m22-tap-drill-size/, published December 8, 2026. Every row is in the CSV download. If a number is wrong, write to contact@tapdrillsize.com and we will correct it.
Chart drills from Starrett, Champion Cutting Tool, Emuge and Hartner (Gühring group); Bolt Depot's metric chart has no M22 row. Class 6H limits from Emuge and Hartner (Gühring group), fine pitch rows from Hartner (Gühring group). 7/8-9 class 2B limits and the thread percentage formula from the OSG chart. Form tap drill from Haas. Spanner and hex key sizes from Wikipedia. Drill diameters from Wikipedia. Published on December 8, 2026.